Home » Cisco Manuals » Networking » Cisco AS5200 » Manual Viewer

Cisco AS5200 Installation Guide - Page 14

Conﬁgure the Universal Access Server - commands

Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

3 Configure the Universal Access Server Use any of the following options for configuring your universal access server: • Cisco Fast Step software • Cisco IOS Release setup script • Command line interface The option you select depends on how you want to configure your universal access server. Use the information on this page to help you decide which option to select. Using Cisco Fast Step Software Cisco Fast Step is a setup utility with a graphical user interface. It provides easy, step-by-step instructions for setting up some of the most commonly used options available on the Cisco AS5200 universal access server. Use Cisco Fast Step to configure your access server with the following options: • Protocols and services (IP, IPX, and NetBEUI) 12 • LAN or WAN topology of 10BaseT, 10/100BaseT, and serial ports • Controller settings (PRI or channelized T1/E1 interfaces) • WAN encapsulation settings (Frame Relay and HDLC) • LAN or WAN side IP or IPX settings • Dial-in side IP or IPX settings • IP address pools or DHCP server settings for dial-in users • Access server security and security server settings • Routing protocol settings including default and user defined (static) routes Using Other Options For all other configurations, use the Cisco IOS Release setup script or the command line interface. Refer to the Cisco AS5200 Universal Access Server Software Configuration Guide for detailed instructions on using the command line interface to configure your Cisco AS5200 universal access server.

Section	Page
Quick Start Guide CiscoAS5200 Universal Access Server Install and Configure	1
Tools and Equipment	1
Install the Universal Access Server	1
Configure the Universal Access Server	1
1Tools and Equipment	3
Items Included	3
Items Not Included	3
Ordering Information	3
2Install the Universal Access Server	4
Prepare the Chassis for Rack-Mounting	4
Step1 Attach the brackets using one of the three methods shown above.	4
Step2 Install the chassis in a rack.	4
2Install the Universal Access Server (continued)	5
Prepare the Chassis for Desktop Use	5
Step1 Locate the rubber feet on the black adhesive strip that shipped with the chassis.	5
Step2 Place the access server upside-down on a flat, smooth surface.	5
Step3 Peel off the rubber feet from the black adhesive strip and place them adhesive-side down o...	5
Step4 Place the access server right-side up on a flat, smooth, secure surface.	5
2Install the Universal Access Server (continued)	6
Connect the Ethernet Port for 10BaseT Ethernet LAN Access	6
Step1 Connect an Ethernet transceiver to the port labeled AUI on the rear panel of the access se...	6
Step2 Connect an Ethernet cable to the Ethernet transceiver.	6
Step3 Connect the other end of the Ethernet cable to a 10BaseT hub.	6
2Install the Universal Access Server (continued)	7
Connect the Ethernet Port for Thick Ethernet LAN Access	7
Step1 Connect your Ethernet AUI cable to the port labeled AUI on the rear panel of the access se...	7
Step2 Connect the other end of the Ethernet cable to an Ethernet hub.	7
2Install the Universal Access Server (continued)	8
Connect the Dual T1/PRI Card for WAN Access	8
Step1 Connect one end of the straight-through RJ-48C-to-RJ-48C cable to the port labeled Port 0 ...	8
Step2 Connect the other end of the cable to an RJ-48C jack.	8
Step3 Repeats steps 1 and 2 to connect a second cable to the port labeled Port 1.	8
2Install the Universal Access Server (continued)	9
Connect the Dual E1/PRI Card for WAN Access	9
Step1 Connect one end of the E1 cable to the port labeled Port 0 on the rear panel of the access...	9
Step2 Connect the other end of the cable to an E1 networks terminating unit.	9
Step3 Repeats steps 1 and 2 to connect a second cable to the port labeled Port 1.	9
2Install the Universal Access Server (continued)	10
Connect the Synchronous Serial Port for WAN Access	10
Step1 Connect one end of a serial transition cable to the port labeled Serial.	10
Step2 Connect the other end of the cable to a CSU/DSU or other DCE (such as a modem).	10
2Install the Universal Access Server (continued)	11
Connect to a Console for Local Administrative Access	11
Step1 Connect one of the adapters, labeled TERMINAL, to the communications port (usually labeled...	11
Step2 Connect one end of the RJ-45-to-RJ-45 rollover cable to the adapter.	11
Step3 Connect the other end of the RJ-45-to-RJ-45 rollover cable to the port labeled CONSOLE on ...	11
Step4 Configure your PC terminal emulation software or terminal for 9600 baud, 8 data bits, no p...	11
2Install the Universal Access Server (continued)	12
Connect a Modem for Remote Administrative Access (Optional)	12
Step1 Connect the adapter labeled MODEM to your modem.	12
Step2 Connect the RJ-45-to-RJ-45 rollover cable to the adapter.	12
Step3 Connect the other end of the RJ-45-to-RJ-45 rollover cable to the port labeled AUX on the ...	12
2Install the Universal Access Server (continued)	13
Connect a Power Cable and Power on the Universal Access Server	13
Step1 Connect one end of the power cord to the power connector on the rear panel of the access s...	13
Step2 Connect the other end of the power cord to the power outlet.	13
Step3 Power ON the access server. Messages will begin to appear on your console screen.	13
3 Configure the Universal Access Server	14
Using Cisco Fast Step Software	14
Using Other Options	14
3 Configure the Universal Access Server (continued)	15
Install and Run Cisco Fast Step	15
1 Insert the Cisco Fast Step CD-ROM (attached to the inside back cover of this guide) into the CD...	15
2 The Fast Step install program starts Setup.exe automatically. If it does not, use the following...	15
(a) Double-click the My Computer icon on your computer desktop.	15
(b) Double-click the CD icon.	15
(c) Double-click the Setup.exe icon.	15
Configure the Universal Access Server	15
AGather Configuration Information	16