Cisco ASA5550-BUN-K9 Hardware Installation Guide - Page 38

Removing and Replacing a Lithium Battery in the SSM, Removing and Replacing the Power Supply

Get Cisco ASA5550-BUN-K9 - ASA 5550 Firewall Edition Bundle PDF manuals and user guides
UPC - 882658096334
View all Cisco ASA5550-BUN-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Removing and Replacing a Lithium Battery in the SSM Chapter 4 Maintenance and Upgrade Procedures Removing and Replacing a Lithium Battery in the SSM To remove and replace the battery in the SSM, perform the following steps: Step 1 Step 2 Step 3 Step 4 Step 5 Remove the two screws at the left rear end of the chassis, and remove the slot cover as described in "Installing and Replacing the Intelligent SSM" section on page 4-20. Slide the metal clip back and pull the battery out. Place the used battery aside. Replace the battery with a compactible Lithium CR-2032 battery (which is available at your local electronics or drug store), by sliding the metal clip back and sliding the battery into place. Replace the chassis cover as described in the "Installing and Replacing the Intelligent SSM" section on page 4-20. Removing and Replacing the Power Supply For information on power supply considerations including environmental operating ranges and power requirements, see table 7 at the following url: http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/product_data_sheet0900a ecd802930c5.html For information on AC-input power cord options, see Table 2-1in the "Power Supply Considerations" section on page 2-4 This section describes how to remove and replace the power supply, and includes the following topics: • Removing the AC Power Supply, page 4-4 • Replacing the AC Power Supply, page 4-6 Removing the AC Power Supply To remove the AC power supply, perform the following steps: Step 1 Step 2 Step 3 Step 4 Step 5 Power off the adaptive security appliance. Remove the power cord and all other cables from the chassis. Remove the chassis from the rack if it is rack-mounted. Remove the chassis cover. See the "Installing and Replacing the Intelligent SSM" section on page 4-20 for more information. Place the chassis in an ESD-controlled environment. See the "Working in an ESD Environment" section on page 4-3 for more information. Cisco ASA 5500 Series Hardware Installation Guide 4-4 78-17989-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
4-4
Cisco ASA 5500 Series Hardware Installation Guide
78-17989-01
Chapter 4
Maintenance and Upgrade Procedures
Removing and Replacing a Lithium Battery in the SSM
Removing and Replacing a Lithium Battery in the SSM
To remove and replace the battery in the SSM, perform the following steps:
Step 1
Remove the two screws at the left rear end of the chassis, and remove the slot cover as described in
“Installing and Replacing the Intelligent SSM” section on page 4-20
.
Step 2
Slide the metal clip back and pull the battery out.
Step 3
Place the used battery aside.
Step 4
Replace the battery with a compactible Lithium CR-2032 battery (which is available at your local electronics
or drug store), by sliding the metal clip back and sliding the battery into place.
Step 5
Replace the chassis cover as described in the
“Installing and Replacing the Intelligent SSM” section on
page 4-20
.
Removing and Replacing the Power Supply
For information on power supply considerations including environmental operating ranges and power
requirements, see table 7 at the following url:
ecd802930c5.html
For information on AC-input power cord options, see
Table 2-1
in the
“Power Supply Considerations”
section on page 2-4
This section describes how to remove and replace the power supply, and includes the following topics:
•
Removing the AC Power Supply, page 4-4
•
Replacing the AC Power Supply, page 4-6
Removing the AC Power Supply
To remove the AC power supply, perform the following steps:
Step 1
Power off the adaptive security appliance.
Step 2
Remove the power cord and all other cables from the chassis.
Step 3
Remove the chassis from the rack if it is rack-mounted.
Step 4
Remove the chassis cover. See the
“Installing and Replacing the Intelligent SSM” section on page 4-20
for more information.
Step 5
Place the chassis in an ESD-controlled environment. See the
“Working in an ESD Environment” section
on page 4-3
for more information.