Cisco ASA5550-BUN-K9 Hardware Installation Guide - Page 41

Installing the DC Model

Get Cisco ASA5550-BUN-K9 - ASA 5550 Firewall Edition Bundle PDF manuals and user guides
UPC - 882658096334
View all Cisco ASA5550-BUN-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Chapter 4 Maintenance and Upgrade Procedures Installing the DC Model Step 3 Insert the power supply brace and press down until it fits into place, as shown in Figure 4-8. Figure 4-8 Replacing the Power Supply Brace and the AC Power Supply 4 3 119579 2 1 1 Back panel 2 Power supply 3 Power supply brace 4 Front panel Step 4 Step 5 Step 6 Connect the power connector to the system board. Replace the adaptive adaptive security appliance cover. See "Replacing the Chassis Cover" for more information. Reinstall the network interface cables. Installing the DC Model Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position. Statement 7 Note The DC return connection should remain isolated from the system frame and chassis (DC-I). This equipment is suitable for connection to intra-building wiring only. To install the DC power model, perform the following steps: 78-17989-01 Cisco ASA 5500 Series Hardware Installation Guide 4-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
4-7
Cisco ASA 5500 Series Hardware Installation Guide
78-17989-01
Chapter 4
Maintenance and Upgrade Procedures
Installing the DC Model
Step 3
Insert the power supply brace and press down until it fits into place, as shown in
Figure 4-8
.
Figure 4-8
Replacing the Power Supply Brace and the AC Power Supply
Step 4
Connect the power connector to the system board.
Step 5
Replace the adaptive adaptive security appliance cover. See
“Replacing the Chassis Cover”
for more
information.
Step 6
Reinstall the network interface cables.
Installing the DC Model
Warning
Before performing any of the following procedures, ensure that power is removed from the DC circuit.
To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC
circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit
breaker in the OFF position.
Statement 7
Note
The DC return connection should remain isolated from the system frame and chassis (DC-I). This
equipment is suitable for connection to intra-building wiring only.
To install the DC power model, perform the following steps:
1
Back panel
3
Power supply brace
2
Power supply
4
Front panel
119579
3
1
2
4