Cisco WS-C3560X-48PF-S Hardware Installation Guide - Page 37

Installation Guidelines, Statement 371-Power Cable and AC Adapter

Get Cisco WS-C3560X-48PF-S PDF manuals and user guides View all Cisco WS-C3560X-48PF-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Chapter 2 Switch Installation Preparing for Installation Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection: 10/100/1000 Ethernet. Statement 1044 Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Statement 371-Power Cable and AC Adapter Caution To comply with the Telcordia GR-1089 Network Equipment Building Systems (NEBS) standard for electromagnetic compatibility and safety, connect the Ethernet cables only to intrabuilding or nonexposed wiring or cabling. Caution To comply with the Telcordia GR-1089 NEBS standard, PoE or non-PoE 10/100/1000 Ethernet port cables that exit from either the left or right side of the switch should be routed and tied to the nearest rack metal. Note The grounding architecture of this product is DC-isolated (DC-I) Installation Guidelines Before installing the switch, verify that these guidelines are met: • Clearance to front and rear panels is such that - Front-panel indicators can be easily read. - Access to ports is sufficient for unrestricted cabling. - AC power cord can reach from the AC power outlet to the connector on the switch rear panel. - The SFP or SFP+ module minimum bend radius and connector length is met. See the SFP or SFP+ module documentation for more information. • For switches with the optional 1100-W power-supply module (C3KX-PWR-1100WAC=), first rack-mount the switch before installing the power-supply module. • Make sure power-supply modules and fan modules are securely inserted in the chassis before moving the switch. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
2-3
Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
OL-19593-02
Chapter 2
Switch Installation
Preparing for Installation
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning
For connections outside the building where the equipment is installed, the following ports must be
connected through an approved network termination unit with integral circuit protection: 10/100/1000
Ethernet.
Statement 1044
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
Statement 371—Power Cable and AC Adapter
Caution
To comply with the Telcordia GR-1089 Network Equipment Building Systems (NEBS) standard for
electromagnetic compatibility and safety, connect the Ethernet cables only to intrabuilding or
nonexposed wiring or cabling.
Caution
To comply with the Telcordia GR-1089 NEBS standard, PoE or non-PoE 10/100/1000 Ethernet port
cables that exit from either the left or right side of the switch should be routed and tied to the nearest
rack metal.
Note
The grounding architecture of this product is DC-isolated (DC-I)
Installation Guidelines
Before installing the switch, verify that these guidelines are met:
•
Clearance to front and rear panels is such that
–
Front-panel indicators can be easily read.
–
Access to ports is sufficient for unrestricted cabling.
–
AC power cord can reach from the AC power outlet to the connector on the switch rear panel.
–
The SFP or SFP+ module minimum bend radius and connector length is met. See the SFP or
SFP+ module documentation for more information.
•
For switches with the optional 1100-W power-supply module (C3KX-PWR-1100WAC=), first
rack-mount the switch before installing the power-supply module.
•
Make sure power-supply modules and fan modules are securely inserted in the chassis before
moving the switch.