Compaq Presario CQ57-300 Maintenance and Service Guide - Page 52

Remove the four Phillips PM 2.5×6.0 screws, Release the hard drive connector cable from the clips

Get Compaq Presario CQ57-300 PDF manuals and user guides View all Compaq Presario CQ57-300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

2. Lift the rear edge of the hard drive compartment cover (2) up and forward until it rests at an angle. 3. Remove the hard drive compartment cover. The hard drive compartment cover is available in the Plastics Kit, spare part number 646131-001. 4. Disconnect the hard drive connector cable (1) from the system board. 5. Release the hard drive connector cable from the clips (2) built into the base enclosure. 6. Remove the four Phillips PM 2.5×6.0 screws (3) that secure the hard drive to the computer. 7. Remove the hard drive (4). 44 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
2.
Lift the rear edge of the hard drive compartment cover
(2)
up and forward until it rests at
an angle.
3.
Remove the hard drive compartment cover. The hard drive compartment cover is available in the
Plastics Kit, spare part number 646131-001.
4.
Disconnect the hard drive connector cable
(1)
from the system board.
5.
Release the hard drive connector cable from the clips
(2)
built into the base enclosure.
6.
Remove the four Phillips PM 2.5×6.0 screws
(3)
that secure the hard drive to the computer.
7.
Remove the hard drive
(4)
.
44
Chapter 4
Removal and replacement procedures