Craftsman 020395 Operation Manual - Page 7

Unpackthepressurewasher, Cartoncontents, Assemblingpressurewasher

Get Craftsman 020395 - 2800 Max PSI PDF manuals and user guides View all Craftsman 020395 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Your pressure washer requires some assembly and is ready for use only after it has been properly serviced with the recommended oil and fuel. If you have any problems with the assembly of your pressurewasher, please call the pressurewasher helpline at 1-800-222-3136. UNPACKTHE PRESSUREWASHER 1. Remove everything from carton except pressure washer. 2. Open carton completely by cutting each corner from top to bottom. 3. Remove pressure washer from carton. CARTONCONTENTS Check all contents. If any parts are missing or damaged, call the pressure washer helpline at 1-800-222-3136. • Main Unit • Handle • Accessory Tray • High Pressure Hose • Spray Gun • Spray Tip Extension with Quick Connect Fitting • Oil Bottle • Hose Wrap • DetergentSiphoning Hose/Filter • Bottle Bracket Wireform • PerfectMixTM Siphoning Unit/Hose • Parts Bag (which includes the following): • Operator's Manual • Owner's Registration Card • Bag containing 4 multi-colored Spray Tips • HandleFasteningHardwareKit (which includes): • Handle Bolts (2) • Carriage Bolt (1) • Plastic Knobs for Handle (2) • Rope Guide (1) • Plastic Knob (2) • Tree Clips (4) Become familiar with each piece before assembling the pressure washer Identify all contents with the illustration on page 6 If any parts are missing or damaged, call the pressure washer helpline at 1-800-222-3136. ASSEMBLINGPRESSUREWASHER Your Craftsman pressure washer will need assembly before operation: 1 Fill out and send in registration card 2 Attach handle and accessory tray 3 Connect detergent siphon hose to pump 4 Add oil to engine crankcase 5 Add fuel to fuel tank 6 Connect pressure hose to spray gun and pump 7 Connectwater supply to pump 8 Attach spray tip extension to spray gun 9 Select/attach quick connect spray tip to spray tip extension Attach Handle and Accessory Tray 1 Place handle (A) onto handle supports (B) connected to main unit Make sure holes (6) in handle align with holes (6) on handle supports , Insert handle carriage bolts (D) through holes from inside of unit and attach a plastic knob (E) from outside of unit Tighten by hand By loosening both knobs to the middle section of the attachment bolt, the upper handle can fold forward to store flat atop the cold engine Note: DO NOTfold the handle down while the engine is hot , Placeaccessory tray (F) over holes (6) on handle (viewing from back of unit) Push the tree clips (H) into the holes until they sit flat against the accessory tray / , Insert multi-colored Quick Connect spray tips and other supplied accessories in spaces provided in accessory tray See How to Use Accessory Tray

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Your pressure washer requires some assembly and is ready
for use only after it has been properly serviced with the
recommended oil and fuel.
If you have any
problems
with the assembly of your
pressurewasher, please call the pressurewasher helpline
at 1-800-222-3136.
UNPACKTHEPRESSUREWASHER
1.
Remove everything from carton except pressure washer.
2.
Open carton completely by cutting each corner from top
to bottom.
3.
Remove pressure washer from carton.
CARTONCONTENTS
Check all contents. If any parts are missing or damaged, call
the pressure washer helpline at
1-800-222-3136.
•
Main Unit
•
Handle
•
Accessory Tray
•
High Pressure Hose
•
Spray Gun
•
Spray Tip Extension with Quick Connect Fitting
•
Oil Bottle
•
HoseWrap
•
DetergentSiphoning Hose/Filter
•
Bottle Bracket Wireform
•
PerfectMix
TM
Siphoning Unit/Hose
•
Parts Bag (which includes the following):
•
Operator's Manual
•
Owner's Registration Card
•
Bag containing 4 multi-colored Spray Tips
•
HandleFasteningHardwareKit (whichincludes):
•
Handle Bolts (2)
•
Carriage Bolt (1)
•
Plastic Knobs for Handle (2)
•
Rope Guide (1)
•
Plastic Knob (2)
•
Tree Clips (4)
Become familiar with each piece before assembling the
pressure washer Identify all contents with the illustration on
page 6 If any parts are missing or damaged, call the
pressure washer helpline at 1-800-222-3136.
ASSEMBLINGPRESSUREWASHER
Your Craftsman pressure washer will need assembly before
operation:
1
Fill out and send in registration card
2
Attach handle and accessory tray
3
Connect detergent siphon hose to pump
4
Add oil to engine crankcase
5
Add fuel to fuel tank
6
Connect pressure hose to spray gun and pump
7
Connectwater supply to pump
8
Attach spray tip extension to spray gun
9
Select/attach quick connect spray tip to spray tip
extension
Attach Handle and Accessory Tray
1
Place handle (A) onto handle supports (B) connected to
main unit Make sure holes (6) in handle align with holes
(6) on handle supports
,
,
,
Insert handle carriage bolts (D) through holes from
inside of unit and attach a plastic knob (E) from outside
of unit Tighten by hand By loosening both knobs to the
middle section of the attachment bolt, the upper handle
can fold forward to store flat atop the cold engine Note:
DO NOTfold the handle down while the engine is hot
Placeaccessory tray (F) over holes (6) on handle
(viewing from back of unit)
Push the tree clips (H) into
the holes until they sit flat against the accessory tray
/
Insert multi-colored Quick Connect spray tips and other
supplied accessories in spaces provided in accessory
tray See
How to Use Accessory Tray