Craftsman 21194 Operation Manual - Page 40

See Basic Saw Operation

Get Craftsman 21194 - 7-1/4 in. Sliding Compound Miter Saw PDF manuals and user guides View all Craftsman 21194 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

TROUBLESHOOTING GUIDE =SAW OPERATION PROBLEM PROBLEM CAUSE SUGGESTED CORRECTIVE ACTION Blade hits table. 1. Misalignment. 1. See ADJUSTMENT -Setting Angle of cut not 1. Miter table unlocked. accurate. Can 2. Sawdust under table. not adjust miter. Cutting Depth section. 1. See OPERATION - Miter Angle Adjustment section. 2. Vacuum or blow out dust. WEAR EYE PROTECTION. Cutting arm wobbles. 1. Loose pivot points. 1. Contact Sears Service Center. Cutting arm will 1. Pivot spring not replaced 1. Contact Sears Service Center. not fully raise, or properly after service. 2. Clean and lubricate moving blade guard 2. Sawdust build-up, parts. won't fully close. Blade binds, ams, burns wood. 1. Improper operation. 2. Dull or warped blade. 3. Improper blade size. 4 Wood is moving during cut. 1. See BASIC SAW OPERATION section. 2. Replace or sharpen blade. 3. Replace with 7-1/4 in. diameter blade. 4. Use hold down clamp to secure Saw vibrates or 1. Saw blade not round/ shakes, damaged /loose. 2. Arbor bolt loose. workpiece to table. 1. Replace blade. 2. Tighten arbor bolt.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
TROUBLESHOOTING
GUIDE =
SAW
OPERATION
SUGGESTED
CORRECTIVE
PROBLEM
PROBLEM
CAUSE
ACTION
Blade hits table.
1. Misalignment.
1. See ADJUSTMENT
-Setting
Cutting Depth section.
Angle of cut not
1.
Miter table unlocked.
1. See OPERATION
- Miter Angle
accurate.
Can
2.
Sawdust under table.
Adjustment
section.
not adjust miter.
2. Vacuum or blow out dust. WEAR
EYE PROTECTION.
Loose pivot points.
1. Contact Sears Service Center.
Pivot spring not replaced 1.
Contact Sears Service Center.
properly after service.
2.
Clean and lubricate
moving
Sawdust build-up,
parts.
Cutting arm
1.
wobbles.
Cutting arm will
1.
not fully raise, or
blade guard
2.
won't fully close.
Blade binds,
1.
ams, burns
2.
wood.
3.
4
Improper
operation.
Dull or warped blade.
Improper
blade size.
Wood is moving during
cut.
Saw vibrates or
1.
Saw blade not round/
1.
shakes,
damaged
/loose.
2.
2. Arbor bolt loose.
1.
See BASIC SAW OPERATION
section.
2.
Replace or sharpen blade.
3.
Replace with 7-1/4 in. diameter
blade.
4.
Use hold down clamp to secure
workpiece to table.
Replace blade.
Tighten
arbor bolt.