Craftsman 28924 Operation Manual - Page 26

Engine

Page 26 highlights

REPLACING BATTERY n_a sWbyARaNlloINwGin:g aDworennocht shoorrtanybaotttehreyr toebrjmeci-t to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. 1. Lift seat pan to raised position. Seat Pan ----.._ INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts manual. TO REPLACE FUSE Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TO REMOVE HOOD & GRILL ASSEMBLY 1. Raise hood. 2. Unsnap headlight wire connector. 3. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. . When replacing hood, be sure to reconnect the headlight wire connector. 2. Disconnect BLACKbatterycablefirstthen RED battery cable and carefully remove battery from tractor. 3. Install new battery with terminals position as old battery. in same 4. First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal 5. Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely. Terminal Cover Keps Nut Hex Bolt Positive (Red) Cable Negative (Black) Cable TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Remove bulb holder from the hole in the backside of the grill. 3. Replace bulb in holder and install bulb holder securely back into the hole in the backside of the grill. 4. Close hood. Hood Headlight Wire Connector ENGINE TO ADJUST THROTTLE CONTROL The throttle control has been preset at the factory and adjustment should not be necessary Check adjustment as described below before loosening cable. If adjustment is necessary, see engine manual. TO ADJUST CHOKE CONTROL The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual. TO ADJUST CARBURETOR Your carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. Ifthe engine does need adjustment, see engine manual. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

REPLACING
BATTERY
n_asWARNING:
Do not short
battery
termi-
by allowing
a wrench
or any other
object
to contact
both
terminals
at the
same
time.
Before
connecting
battery,
remove
metal
bracelets,
wristwatch
bands,
rings,
etc.
Positive
terminal
must
be connected
first
to
prevent
sparking
from
accidental
grounding.
1.
Lift seat
pan
to raised
position.
Seat Pan ----.._
2.
Disconnect
BLACKbatterycablefirstthen
RED
battery
cable
and
carefully
remove
battery
from
tractor.
3.
Install
new
battery
with terminals
in same
position
as
old
battery.
4.
First
connect
RED
battery
cable
to posi-
tive
(+) terminal
with
hex
bolt
and
keps
nut
as
shown.
Tighten
securely.
Slide
terminal
cover
over
terminal
5.
Connect
BLACK
grounding
cable
to
negative
(-) terminal
with
remaining
hex
bolt and
keps
nut.
Tighten
securely.
Terminal
Keps
Cover
Nut
Hex
Bolt
Positive
(Red)
Cable
Negative
(Black)
Cable
TO
REPLACE
HEADLIGHT
BULB
1.
Raise
hood.
2.
Remove
bulb
holder
from
the
hole
in
the
backside
of the
grill.
3.
Replace
bulb
in holder
and
install
bulb
holder
securely
back
into
the
hole
in
the
backside
of the
grill.
4.
Close
hood.
INTERLOCKS
AND
RELAYS
Loose or damaged
wiring
may cause
your tractor
to run poorly, stop running,
or
prevent
it from starting.
Check
wiring.
See electrical
wiring
diagram
in the Repair
Parts manual.
TO
REPLACE
FUSE
Replace
with
20 amp
automotive-type
plug-in
fuse.
The
fuse
holder
is located
behind
the
dash.
TO
1.
2.
3.
.
REMOVE
HOOD
& GRILL
ASSEMBLY
Raise
hood.
Unsnap
headlight
wire
connector.
Stand
in front
of tractor.
Grasp
hood
at
sides,
tilt toward
engine
and
lift off of
tractor.
When
replacing
hood,
be sure
to
re-
connect
the
headlight
wire
connector.
Hood
Headlight
Wire
Connector
ENGINE
TO
ADJUST
THROTTLE
CONTROL
The
throttle
control
has
been
preset
at
the
factory
and
adjustment
should
not
be
necessary
Check
adjustment
as
described
below
before
loosening
cable.
If adjustment
is necessary,
see
engine
manual.
TO
ADJUST
CHOKE
CONTROL
The
choke
control
has
been
preset
at the
factory
and adjustment
should
not be neces-
sary.
If adjustment
is necessary,
see engine
manual.
TO
ADJUST
CARBURETOR
Your carburetor
has been
preset
at the factory
and
adjustment
should
not
be
necessary.
However,
minor
adjustment
may
be required
to
compensate
for
differences
in fuel,
tem-
perature,
altitude
or load.
Ifthe
engine
does
need
adjustment,
see
engine
manual.
26