Craftsman 7-1/4 Operation Manual - Page 12

DO NOT attempt

Get Craftsman 7-1/4 - in. Circular Saw with Laser Trac and LED Worklight PDF manuals and user guides View all Craftsman 7-1/4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Non-Through Cuts Any cutting operation where the blade does not extend completely through the thickness of the workpiece, like a dado cut. Leading End The end of the workpiece pushed into tool firsL Kerr The material removed by the blade in a through cut or the slot produced by the blade in a non-through or partial cut Kickback A hazard that can occur when the blade binds or stalls, throwing the workpiece back toward operator. Workpiece or Material The item on which the cutting operation is being done_ The surfaces of a workpiece are commonly referred to as faces, ends and edges. Gum A sticky, sap-based residue from wood products. Resin A sticky, sap-based substance that has hardened. /_ WARNING: Your saw should NEVER be connected to the power source when you are assembling parts, making adjustments, installing or removing blades, cleaning or when It is not In use. Disconnecting the saw will prevent accidental starting, which could cause serious personal Injury. 1. The saw's cutting blade is installed at the factory. 2. The edge guide is force-fitted into the top of the lid of the storage/carrying case. 3. The blade wrench is also force-fitted into the top of the lid of the case. The wrench is used when changing or installing a new blade. 4. Also included and attached to the top of the lid of the case with a hook and loop strap is a pair of Laser enhancing safety glasses which are used to enhance the laser beam in bright light conditions. 5o There Is a blade storage area in the bottom of the case where an extra blade can be stored. 6. Inspect the saw carefully to make sure that no breakage or damage has occurred during shipping, tf any of the items mentioned are missing (refer to PARTS LIST on page 13), return the saw to your nearest Sears store or Craftsman outlet to have the saw replaced. in the power cord or operate saw until the broken or missing parts are replaced. F_ailurWe AtoRdNoINsGo :coulIdf arneysuplat rtIsn aproessblrbolekenseroiorumslssInlnjugr,y. DO NOT attempt to plug 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Non-Through
Cuts
Any cutting operation
where
the blade does not extend completely
through the
thickness of the workpiece,
like a dado cut.
Leading
End
The end
of
the workpiece pushed into tool
firsL
Kerr
The material
removed by the blade
in
a through cut or the slot produced by the blade
in a non-through
or partial cut
Kickback
A hazard that can occur when the blade binds or stalls, throwing the workpiece
back
toward operator.
Workpiece
or
Material
The item on which the cutting operation
is
being done_ The surfaces of a workpiece
are commonly
referred to as faces, ends and edges.
Gum
A sticky, sap-based
residue from wood products.
Resin
A sticky, sap-based
substance that has hardened.
/_
WARNING:
Your
saw
should
NEVER be connected
to the power source
when you are assembling
parts, making adjustments,
installing or removing
blades, cleaning
or when It is not In use. Disconnecting
the saw will prevent
accidental
starting, which could cause serious
personal
Injury.
1. The
saw's cutting blade is
installed at
the
factory.
2.
The
edge guide is
force-fitted
into
the top of the lid of the
storage/carrying
case.
3. The blade
wrench
is also force-fitted
into the top of the lid of the case. The wrench
is used when changing
or installing a new blade.
4. Also included and attached
to the top of the lid of the case with a hook and loop strap
is a pair of
Laser enhancing
safety glasses
which are used to enhance the laser
beam
in
bright light conditions.
5o There Is a blade storage area in the bottom of the case where
an extra blade can
be stored.
6.
Inspect the saw carefully to make sure that no breakage
or damage
has occurred
during shipping,
tf any of the items mentioned
are missing
(refer to PARTS LIST
on page 13), return the saw to your nearest Sears store or Craftsman
outlet
to have the saw replaced.
_
WARNING:
If
any parts are broken
or
mlsslng,
DO NOT attempt
to plug
in the power
cord or operate saw until the broken
or missing parts are replaced.
Failure to do so could result In posslble serious
Injury.
12