Craftsman 7-1/4 Operation Manual - Page 23

Installingand Using, Theedgeguidecont.

Get Craftsman 7-1/4 - in. Circular Saw with Laser Trac and LED Worklight PDF manuals and user guides View all Craftsman 7-1/4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

INSTALLINGAND USING THE EDGEGUIDEcont. 6, Place the edge guide firmly against the edge of the workpiece (See Fig,, 13a), Doing this wilt give you a true cut without pinching the blade, 7, BE SURE that the guiding edge of the workpiece is straight so you can get a straight cut, 8, ALWAYS LET THE BLADE REACH FULL SPEED, then Fig. carefully guide the saw into the workpiece. DO NOT bind the blade in the cut Push the saw forward at a speed where the blade is not laboring, HOW TO SET YOUR BEVEL ANGLE (Fig. 14) 1, Unplug the saw zuin_njuprlyu°Wg AthRe NsaINwGc;ouldALreWsuAlYt Sinuancpcluidgenstaalw sbteafrolirneg mwahkiicnhg caanny caadujusestmseenritosu° s Fpaeilrusroenatlo 2. Loosen bevel adjustment lever (see Fig.14). 3 Raise the motor housing end of the saw until you reach the desired angle setting on the bevel scale 4, Tighten the adjustment lever securely, Bevel Fig° 14 23 I i __J.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
INSTALLINGAND USING
THEEDGEGUIDEcont.
6,
Place the edge guide firmly
against the
edge
of the workpiece
(See Fig,, 13a), Doing this wilt
give you a true cut without
pinching the blade,
7,
BE SURE that the guiding
edge of the workpiece
is
straight so you can get
a straight cut,
8, ALWAYS LET THE BLADE
REACH
FULL SPEED, then
carefully
guide the saw into the
workpiece.
DO NOT bind the
blade in the cut
Push the
saw forward at a speed where
the blade is not laboring,
Fig.
HOW
TO
SET
YOUR
BEVEL
ANGLE
(Fig.
14)
1,
Unplug the saw
z_
WARNING;
ALWAYS unplug
saw before
making
any
adjustments°
Failure
to
unplug
the saw
could
result
in
accidental
starling
which
can cause
serious
personal
injury°
2.
Loosen bevel adjustment lever (see Fig.14).
3
Raise the motor housing
end
of the saw
Bevel
until you reach the desired angle setting
on the bevel scale
4,
Tighten the adjustment lever securely,
Fig° 14
I
i
__J.
23