D-Link DCS-910 Product Manual - Page 26

Setup > Wireless - setup to the router

Get D-Link DCS-910 - SECURICAM 10/100 Fast Ethernet Internet Camera Network PDF manuals and user guides
UPC - 790069313776
View all D-Link DCS-910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Section 3 - Configuration Setup > Wireless In this section, you can setup and configure the wireless settings on your camera. Note: Wireless is available only for the DCS-920. Wireless Interface SSID: Service Set Identifier, an identifier for your wireless network. Channel: The default setting is channel 6. Select the same channel that is using by other wireless devices within your network. When there is interference from the wireless networks that overlap with one another, you may change the channel to obtain maximum performance for your connection. Connection Mode: Infrastructure is a wireless connection using an access point as a transmission point of all wireless devices. Ad-Hoc is a wireless connection used without an access point, where your DCS-920 is directly connecting to your PC. This is done using the onboard wireless adapter on the DCS-920 connected to a wireless adapter on the PC. Survey: This page will allow you to select a wireless network that the DCS-920 was able to detect upon booting up. Wireless Security For security, there are three choices; None, WEP, and WPA-PSK / WPA2-PSK. Select the same encryption method that is being Mode: used by your wireless device/ router. WPA-PSK / WPA2PSK An appropriate Preshared Key, which is needed in order to connect to the wireless network.. Settings: D-Link DCS-910/920 User Manual 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
±µ
D-Link DCS-910/9±0 User Manual
Section ² - Configuration
Setup > Wireless
Service Set Identifier, an identifier for your wireless network.
The default setting is channel 6. Select the same channel that is using by other wireless devices within your network. When there is
interference from the wireless networks that overlap with one another, you may change the channel to obtain maximum performance
for your connection.
Infrastructure
is a wireless connection using an access point as a transmission point of all wireless devices.
Ad-Hoc
is a wireless
connection used without an access point, where your DCS-920 is directly connecting to your PC. This is done using the on-
board wireless adapter on the DCS-920 connected to a wireless adapter on the PC.
This page will allow you to select a wireless network that the DCS-920 was able to detect upon booting up.
For security, there are three choices;
None
,
WEP
, and
WPA-PSK / WPA2-PSK
. Select the same encryption method that is being
used by your wireless device/ router.
An appropriate
Preshared Key
, which is needed in order to connect to the wireless network..
SSID:
Channel:
Connection Mode:
Survey:
Wireless Security
Mode:
WPA-PSK / WPA2PSK
Settings:
Wireless Interface
In this section, you can setup and configure the wireless
settings on your camera.
Note:
Wireless is available only for the DCS-920.