D-Link DIS-300G-14PSW CLI Manual

D-Link DIS-300G-14PSW Manual

Get D-Link DIS-300G-14PSW PDF manuals and user guides View all D-Link DIS-300G-14PSW manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DIS-300G-14PSW manual content summary:

  • D-Link DIS-300G-14PSW | CLI Manual - Page 1
    DIS-300G Series Industrial Managed Ethernet Switch CLI Reference Guide Rev 0.1
  • D-Link DIS-300G-14PSW | CLI Manual - Page 2
  • D-Link DIS-300G-14PSW | CLI Manual - Page 3
    Contents CONTENTS 1 SCOPE ...3 1.1 SCOPE ...3 1.2 AUDIENCE ...3 1.3 PRE-REQUIRED KNOWLEDGE...3 1.4 ACCESS TO HARDWARE INTERFACE ...3 1.5 RELATED DOCUMENTS...3 2 OPERATOR INTERFACE ...7 2.1 INTRODUCTION ...7 2.2 CONNECT INTERFACE...7 2.3 SCREEN DESCRIPTION ...7 2.4 EXECUTION MODES ...8 2.5 GETTING
  • D-Link DIS-300G-14PSW | CLI Manual - Page 4
    Contents 3.2.29 3.2.30 3.2.31 3.2.32 3.2.33 3.2.34 3.2.35 3.2.36 3.2.37 3.2.38 3.2.39 3.2.40 3.2.41 3.2.42 3.2.43 3.2.44 3.2.45 3.2.46 3.2.47 3.2.48 3.2.49 3.2.50 3.2.51 3.2.52 3.2.53 3.2.54 3.2.55 3.2.56 3.2.57 3.2.58 3.2.59 3.2.60 3.2.61 3.2.62 3.2.63 3.2.64 3.2.65 3.2.66 3.2.67 3.2.68 3.2.69
  • D-Link DIS-300G-14PSW | CLI Manual - Page 5
    Contents 3.2.88 show dot1x status ...29 3.2.89 show dot1x statistics...29 3.2.90 show radius-server [ statistics ] ...29 3.2.91 show rfc2544 profile [ ] ...29 3.2.92 show voice ...30 3.2.93 show web ...30 3.3 CONFIGURE MODE COMMANDS...31 3.3.1 interface gigabit ...31 3.3.2 interface
  • D-Link DIS-300G-14PSW | CLI Manual - Page 6
    Contents 3.3.53 login level ...39 3.3.54 login on...39 3.3.55 logout ...39 3.3.56 mac address-table aging-time ...39 3.3.57 mac address-table static ...39 3.3.58 more...40 3.3.59 no...40 3.3.60 ping...40 3.3.61 port-security ...40 3.3.62 privilege...40 3.3.63 reload ...41 3.3.64 rmon ...41 3.3.65
  • D-Link DIS-300G-14PSW | CLI Manual - Page 7
    Contents 3.5.7 ip dhcp server ...51 3.5.8 ip dhcp relay...51 3.5.9 ip dhcp relay information option ...51 3.5.10 ip dhcp retry interface vlan ...51 3.5.11 ip dhcp snooping ...51 3.5.12 ip helper-address ...51 3.5.13 ipv6 address...51 3.5.14 ipv6mtu ...51 3.6 RINGV2 GROUP MODE COMMANDS ...52 3.6.1
  • D-Link DIS-300G-14PSW | CLI Manual - Page 8
    Contents 3.9.14 snmp-server location ...59 3.9.15 snmp-server security-to-group ...60 3.9.16 SNMP trap receive ipv4 host ...60 3.10 QOS FUNCTION COMMAND...60 3.10.1 qos qce...60 3.10.2 qos storm ...60 3.10.3 qos cos...61 3.10.4 qos dscp-classify...61 3.10.5 qos dscp-remark ...61 3.10.6 qos dscp-
  • D-Link DIS-300G-14PSW | CLI Manual - Page 9
    Contents 3.13.10 ipv6 mld snooping vlan ...68 3.13.11 ipv6 mld ssm-range ...68 3.13.12 ipv6 mld unknown-flooding ...69 3.13.13 ipv6 route...69 3.14 AUTHENTICATE MODE COMMANDS ...69 3.14.1 radius-server attribute 32...69 3.14.2 radius-server attribute 4...69 3.14.3 radius-server attribute 95...69 3.
  • D-Link DIS-300G-14PSW | CLI Manual - Page 10
    Contents 3.18.5 gvrp time { [ join-time ] [ leave-time ] [ leave-all-time
  • D-Link DIS-300G-14PSW | CLI Manual - Page 11
    Contents ix
  • D-Link DIS-300G-14PSW | CLI Manual - Page 12
  • D-Link DIS-300G-14PSW | CLI Manual - Page 13
    1. Scope 1.1 Scope 1.2 Audience 1.3 Pre-required Knowledge 1.4 Access to Hardware Interface 1.5 Related Documents 1
  • D-Link DIS-300G-14PSW | CLI Manual - Page 14
    2
  • D-Link DIS-300G-14PSW | CLI Manual - Page 15
    of the Command Line Interface (CLI) as implemented in the current version of DIS-300G Series software. These commands are used to set-up, administer and maintain the system. 1.2 Audience The guide is intended for Operating personnel (sometimes called craft persons). 1.3 Pre-required Knowledge The
  • D-Link DIS-300G-14PSW | CLI Manual - Page 16
    Scope 4
  • D-Link DIS-300G-14PSW | CLI Manual - Page 17
    2. Operator Interface 2.1 Introduction 2.2 Connect Interface 2.3 Authorization Level 2.4 Screen Description 2.5 Execution Modes 2.6 Getting Help 2.7 Terminal Key Function 2.8 Notation Conventions 5
  • D-Link DIS-300G-14PSW | CLI Manual - Page 18
    6
  • D-Link DIS-300G-14PSW | CLI Manual - Page 19
    , because the initial password is known to anyone who reads this manual. You can also change the user name or add additional user can run terminal emulator such as PuTTY) 2.3 Screen Description 1. Connecting to DIS-300G Ethernet port(RJ45 Ethernet port) 2. Key-in the command under Telnet: telnet
  • D-Link DIS-300G-14PSW | CLI Manual - Page 20
    10.90.90.90 Figure 2-1 Screen Description 2.4 Execution Modes The CLI contains several execution modes. Users will see different set of commands under different execution modes. Table 2-1 lists all the execution modes and their purposes. When users enter a certain execution mode, the
  • D-Link DIS-300G-14PSW | CLI Manual - Page 21
    Operator Interface 2.6 Terminal Key Function Following is the list of all the terminal keys and their function. ENTER CTRL-M TAB CTRL-I ? CTRL-P CTRL-N Home CTRL-A End CTRL-E CTRL-B CTRL-F BACKSPACE CTRL-H Table 2-2 List of Terminal Keys Run a
  • D-Link DIS-300G-14PSW | CLI Manual - Page 22
    10
  • D-Link DIS-300G-14PSW | CLI Manual - Page 23
    3. Commands Descriptions 3.1 Initialize Mode Commands 3.2 Enable Mode Commands 3.3 Configure Mode Commands 3.4 VLAN Mode Commands 3.5 Interface VLAN Mode Commands 3.6 Ring Group Mode Commands 3.7 Spanning Tree Configure Commands 3.8 sFlow Configure Command 3.9 SNMP Configure
  • D-Link DIS-300G-14PSW | CLI Manual - Page 24
    3 Commands Descriptions 3.1 Initialize Mode Commands The commands in this section (except 'enable' command) can be executed under all command modes. These commands are global commands. 3.1.1 exit Description Syntax Parameter Exit current mode and quit CLI. exit None 3.1.2 configure terminal
  • D-Link DIS-300G-14PSW | CLI Manual - Page 25
    ] ] [ ace statistics [ ] ] Parameter show access-list ace-status [ static ] [ link-oam ] [ loop-protect ] [ dhcp ] [ ptp ] [ upnp ] [ arp-inspection ] [ : 1~256> ACE ID The ACEs that are configured by users manually The ACEs that are configured by Loop Protect module The ACEs that are
  • D-Link DIS-300G-14PSW | CLI Manual - Page 26
    arp-inspection to hardware limitations The ACEs that are configured by ARP Inspection module 3.2.6 show aggregation Description Aggregation Syntax show aggregation [ mode ] Parameter Name Description mode Traffic distribution mode 3.2.7 show alarm Description Syntax Parameter Alarm
  • D-Link DIS-300G-14PSW | CLI Manual - Page 27
    3.2.11 show ipmc Description Syntax Parameter 3.2.12 show ipv6 Description Syntax Parameter 3.2.13 show lacp Description Syntax Parameter 3.2.14 show line Description Syntax Parameter 3.2.15 show logging Description http igmp interface name-server route source ssh statistics verify Hypertext
  • D-Link DIS-300G-14PSW | CLI Manual - Page 28
    Syntax Parameter show logging [ switch ] show logging [ info ] [ warning ] [ error ] [ switch ] Name log_id error info warning Description Logging ID Error Infomation Warning 3.2.16 show loop-protec Description Loop protect
  • D-Link DIS-300G-14PSW | CLI Manual - Page 29
    Syntax Parameter show running-config feature [ all-defaults ] Name Description feature_name CWORD all-defaults Valid words are 'GVRP' 'access' 'access-list' 'aggregation' 'alm_profile' 'arp-inspection' 'auth' 'clock' 'dhcp' 'dhcp-snooping' 'dhcp_server' 'dns' 'dot1x' '
  • D-Link DIS-300G-14PSW | CLI Manual - Page 30
    Syntax Parameter show version None 3.2.30 show system inventory Description Show system inventory. Syntax show system inventory Parameter None 3.2.31 show mac address table aging-time Description Show aging time for MAC learning table (system-wide). Syntax show aging time Parameter None
  • D-Link DIS-300G-14PSW | CLI Manual - Page 31
    Syntax Parameter show mac address-table [ conf | static | aging-time | { { learning | count } [ interface ( [
  • D-Link DIS-300G-14PSW | CLI Manual - Page 32
    Port type in Fast, Giga or Tengiga ethernet Valid values: 1 ~ 10 Type: Mandatory 3.2.42 show fdbstatic vlan Description Show static MAC forwarding table per VLAN index. Syntax show mac address-table { learning | count } vlan Parameter Name Description <
  • D-Link DIS-300G-14PSW | CLI Manual - Page 33
    3.2.44 show interface port statistics Description Show Ethernet counter per gigabit port. Syntax show interface [ ] statistics Parameter Name Description Port type in Fast, Giga or Tengiga ethernet Valid values: 1 ~ 10 Type:
  • D-Link DIS-300G-14PSW | CLI Manual - Page 34
    3.2.48 show profile alarm Description Profile alarm Syntax show profile alarm Parameter None 3.2.49 show sflow Description Syntax Sflow information show sflow Parameter show sflow statistics { receiver [ ] | samplers [ interface [ ] ( [ <
  • D-Link DIS-300G-14PSW | CLI Manual - Page 35
    aaa interface switch system mib context ifmib ifIndex security-to-group security_name user username engineID view view_name oid_subtree configuration AAA event group Interface event group Switch event group System event group MIB(Management Information Base) MIB context IF-MIB The IfIndex that is
  • D-Link DIS-300G-14PSW | CLI Manual - Page 36
    3.2.55 show vlan id Description Syntax Parameter Show bridge port member set/status per VLAN index (1~4094). show vlan id Name Description Valid values: 1~4094 Type: Mandatory. 3.2.56 show vlan name Description Show bridge port member set/status per VLAN name ( 32 words ).
  • D-Link DIS-300G-14PSW | CLI Manual - Page 37
    ipx at llc dsap ssap snap oui rfc-1042 snap-8021h Ether Type is IPX Ether Type is AppleTalk LLC-based VLAN status DSAP (Range: 0x00 - 0xFF) SSAP (Range: 0x00 - 0xFF) SNAP-based VLAN status SNAP OUI (Range 0x000000 - 0XFFFFFF) SNAP OUI is rfc-1042 SNAP OUI is
  • D-Link DIS-300G-14PSW | CLI Manual - Page 38
    Syntax Parameter show queue-shaper None 3.2.66 show port-shaper Description Show port shaper information. Syntax show port-shaper Parameter None 3.2.67 show pvlan [ ] Description PVLAN ID Syntax show pvlan [ ] Parameter Name Description pvlan_list PVLAN ID to
  • D-Link DIS-300G-14PSW | CLI Manual - Page 39
    3.2.72 show qos interface Description QoS interface information Syntax show qos [ { interface [ ( [ ] ) ] } Parameter Name Description interface Interface port_type GigabitEthernet, 1 Gigabit Ethernet Port port PORT_LIST, Port list in 1/1-14 3.2.73 show qos maps
  • D-Link DIS-300G-14PSW | CLI Manual - Page 40
    Parameter None 3.2.78 show rmon Description Syntax Parameter show rmon alarm [ ] show rmon event [ ] show rmon history [ ] show rmon statistics [ ] Name alarm event history statistics id_list Description Display the RMON alarm table Display the RMON event
  • D-Link DIS-300G-14PSW | CLI Manual - Page 41
    Parameter Name Description Gigabit port. Valid values: 1 ~ 10 Type: Mandatory 3.2.85 show vlan-trans Description Show VLAN translation table for all Syntax show vlan-trans Parameter None 3.2.86 show multicast-fdb Description Show IGMP group membership table Syntax show multicast
  • D-Link DIS-300G-14PSW | CLI Manual - Page 42
    3.2.92 show voice Description Syntax Parameter 3.2.93 show web Description Syntax Parameter rfc2544 profile name Vlan for voice traffic show voice vlan [ oui | interface ( [ ] ) ] Name vlan oui oui interface port_type port_list Description Vlan for voice
  • D-Link DIS-300G-14PSW | CLI Manual - Page 43
    3.3 Configure Mode Commands Commands that can be executed under Configure Mode 3.3.1 interface gigabit Description Gigabit Ethernet interface. (enter gigabit interface mode) Syntax interface gigabit Parameter Name Description Valid values: 1 ~ 10 Type: Mandatory
  • D-Link DIS-300G-14PSW | CLI Manual - Page 44
    3.3.7 alarm history clear Description Clear alarm history Syntax alarm history clear Parameter Name Description 3.3.8 banner Description Syntax Parameter Banner control banner { LINE | exec | login | motd } Name LINE exec login motd Description c banner-text c, where 'c' is a delimiting
  • D-Link DIS-300G-14PSW | CLI Manual - Page 45
    an account. Syntax no username Parameter Name Description < word31> Valid values: 1 ~ 31 characters Type: Mandatory 3.3.17 syslog {enable|disable} Description Disable or enable syslog service. Syntax logging on no logging on Parameter None 33
  • D-Link DIS-300G-14PSW | CLI Manual - Page 46
    3.3.18 configuration save and replace Description Save and install configuration Syntax copy { startup-config | running-config | } { startup-config | running-config | < Filename > } [ syntax-check ] Parameter Name Description running- Currently running configuration config
  • D-Link DIS-300G-14PSW | CLI Manual - Page 47
    Syntax Parameter 3.3.25 do Description Syntax Parameter 3.3.26 duplex Description Syntax Parameter 3.3.27 editing Description Syntax Parameter 3.3.28 firmware Description Syntax Parameter 3.3.29 flowcontrol Description Syntax Parameter 3.3.30 frame-sizes Description Syntax Parameter dir To run
  • D-Link DIS-300G-14PSW | CLI Manual - Page 48
    1280 1518 2000 9600 Enable testing with 1280-byte TST PDUs Enable testing with 1518-byte TST PDUs Enable testing with 2000-byte TST PDUs Enable testing with 9600-byte TST PDUs 3.3.31 green-etherneteee Description Powering down of PHYs when there is no traffic. Syntax green-etherneteee
  • D-Link DIS-300G-14PSW | CLI Manual - Page 49
    vlan Parameter Name Description vlan_list arp inspection vlan list 3.3.39 ip dns proxy Description Syntax Parameter IP DNS proxy service ipdns proxy 3.3.40 ip http secure-redirect Description IP http secure-redirect Syntax ip http secure-redirect Parameter 3.3.41 ip
  • D-Link DIS-300G-14PSW | CLI Manual - Page 50
    3.3.45 ip route Description Syntax Parameter 3.3.46 ip routing Description Syntax Parameter 3.3.47 ip verify Description Syntax Parameter 3.3.48 ipmc profile Description Syntax Parameter 3.3.49 ipmc range Description Syntax Parameter 3.3.50 lacp Description Syntax Parameter dhcp v_vlan_id Dynamic
  • D-Link DIS-300G-14PSW | CLI Manual - Page 51
    3.3.51 line Description Syntax Parameter Console terminal control line { | console 0 | vty } Name console vty Description List of line numbers Console terminal line Virtual terminal 3.3.52 login host Description Syntax Parameter Domain name and IP address logging host { <
  • D-Link DIS-300G-14PSW | CLI Manual - Page 52
    3.3.58 more Description Syntax Parameter 3.3.59 no Description Syntax Parameter 3.3.60 ping Description Syntax Parameter 3.3.61 port-security Description Syntax Parameter 3.3.62 privilege Description Syntax Parameter File in FLASH or on TFTP server more Function disable no { debug | port-
  • D-Link DIS-300G-14PSW | CLI Manual - Page 53
    of uni-cast packets delivered to a higher-layer protocol The number of the inbound packets that were discarded because of the unknown or un-support protocol The number of outbound packets that are discarded event the packets is normal The The number of outbound packets that could not be transmitted
  • D-Link DIS-300G-14PSW | CLI Manual - Page 54
    falling_threshold falling_event_id both falling rising crossing falling threshold value Event to fire on falling threshold crossing Trigger alarm when the first value is larger than the rising threshold or less than the falling threshold (default) rigger alarm
  • D-Link DIS-300G-14PSW | CLI Manual - Page 55
    VLAN Name (0~31) String Size:0~31 Type: Mandatory 3.3.70 vlan disable Description Delete VLAN memberset/setting. Syntax vlan disable Parameter Name Description Valid values: 1 ~ 4094 Type: Mandatory 3.3.71 mac address-table aging-time Description
  • D-Link DIS-300G-14PSW | CLI Manual - Page 56
    port_type v_port_type_lis 1 Gigabit Ethernet Port Port list 3.3.76 monitor source cpu Description Mirror Interface traffic Syntax monitor source { cpu [ ] } } { both | rx | tx } Parameter Name Description both Setting source port to both will mirror both ingress and egress
  • D-Link DIS-300G-14PSW | CLI Manual - Page 57
    3.3.81 traps Description Syntax Parameter trap event configuration traps [ aaa authentication ] [ system [ coldstart ] [ warmstart ] ] [ switch [ stp ] [ rmon ] ] Name aaa authentication coldstart warmstart stp rmon Description AAA authentication fail event Cold start event Warm start event STP
  • D-Link DIS-300G-14PSW | CLI Manual - Page 58
    -control. 3.3.88 speed Description Syntax Parameter Configure gigabit Ethernet speed and Copper/SFP for gigabit port 7~8. (port1~6 Only support copper, no SFP) (port 9, 10 only support auto) speed {auto|full-l000mbps|full-100mbps|full-10mbps|half-100mbps|half- 10mbps} Name auto full-l000mbps full
  • D-Link DIS-300G-14PSW | CLI Manual - Page 59
    3.3.90 Date/Time Description Syntax Parameter Set device date and time clock datetime Name Description year month Date Hour minute Second 3.4 VLAN Mode Commands 3.4.1 vlan Description Syntax Parameter
  • D-Link DIS-300G-14PSW | CLI Manual - Page 60
    Parameter 3.4.5 switchport access vlan Description Set switch access mode of the interface Syntax switchport access vlan Parameter Name Description vlan_id VLAN ID of the VLAN when this port is in access mode 3.4.6 switchport forbidden vlan Description Adds or removes forbidden
  • D-Link DIS-300G-14PSW | CLI Manual - Page 61
    3.4.10 switchport hybrid ingress-filtering Description VLAN Ingress filter configuration Syntax switchport hybrid ingress-filtering Parameter 3.4.11 switchport mode Description Set switching mode Syntax switchport mode { access | trunk | hybrid } Parameter Name Description access Set
  • D-Link DIS-300G-14PSW | CLI Manual - Page 62
    3.5 Interface VLAN Mode Commands 3.5.1 interface Description Syntax Parameter Interface configuration interface [ ] Name port_type port_type_list Description Port type in Fast, Giga or Tengigaethernet List of Port ID, ex, 1/1,3-5;2/2-4,6 3.5.2 interface vlan
  • D-Link DIS-300G-14PSW | CLI Manual - Page 63
    3.5.7 ip dhcp server Description Syntax Parameter DHCP Server ip dhcp server 3.5.8 ip dhcp relay Description Syntax Parameter DHCP relay agent configuration ipdhcp relay 3.5.9 ip dhcp relay information option Description IP DHCP relay information option(Option 82) Syntax ipdhcp relay
  • D-Link DIS-300G-14PSW | CLI Manual - Page 64
    3.6 RingV2 Group Mode Commands 3.6.1 ringv2 protect Description Syntax Parameter To configure ring protection. ring protect Name group1 group2 group3 Description Configure ring protection v2 group1 (Ring) Configure ring protection v2 group2 (Ring) Configure ring protection v2 group3 (Chain)
  • D-Link DIS-300G-14PSW | CLI Manual - Page 65
    couplingbackup dual-homing chain-head chainmember chain-tail b-chaincentral-block b-chainmember b-chainterminal-1 b-chainterminal-2 Set role to coupling backup Set role to dual homing Set role to chain head Set role to chain member Set role to chain tail Set role to balancing chain central block
  • D-Link DIS-300G-14PSW | CLI Manual - Page 66
    3.7.7 spanning-tree edge bpdu-filter Description Enable BPDU filter (stop BPDU tx/rx) Syntax spanning-tree edge bpdu-filter Parameter Name Description 3.7.8 spanning-tree mode Description mode STP protocol mode stp 802.1D Spanning Tree rstp Rabid Spanning Tree (802.1w) mstp Multiple
  • D-Link DIS-300G-14PSW | CLI Manual - Page 67
    Priority of the instance 3.7.12 spanning-tree mst vlan Description VLAN keyword Syntax spanning-tree mst vlan Parameter Name Description instance 0-7 (CIST=0, MST2=1...) Range of VLANs 3.7.13 spanning-tree mst forward-time Description
  • D-Link DIS-300G-14PSW | CLI Manual - Page 68
    priority vlan prio v_vlan_list MST2=1...) Priority of the instance VLAN keyword Range in seconds Range of VLANs 3.7.18 spanning-tree recovery Description Recovery Syntax spanning-tree recovery interval Parameter Name Description interval The interval
  • D-Link DIS-300G-14PSW | CLI Manual - Page 69
    receiver list packet byte 3.8.5 sflow max-sampling-size Description Specifies the maximum number of bytes to transmit per flow sample. Syntax sflow max-sampling-size [ sampler ] [ ] Parameter Name Description < range_list > Sampler instance
  • D-Link DIS-300G-14PSW | CLI Manual - Page 70
    Name Description < Name of the host Name of the host configuration configuration > packet byte [ linkup ] Link up event [ linkdown ] Link down event [ lldp ] LLDP event 3.9.7 snmp-server trap Description Set SNMP server's configurations Syntax snmp-server trap Parameter
  • D-Link DIS-300G-14PSW | CLI Manual - Page 71
    32> ] ] Parameter Name Description 32 words word10-32 MD5 Set MD5 protocol sha Set SHA protocol SHA password priv Set Privacy { des | aes } Set DES/AES protocol Set privacy password 3.9.9 snmp-server version Description
  • D-Link DIS-300G-14PSW | CLI Manual - Page 72
    Syntax Parameter snmp-server location Name v_line255 Description location string 3.9.15 snmp-server security-to-group Description SNMP server security Syntax snmp-server security-to-group model { v1 | v2c | v3 } name group Parameter Name
  • D-Link DIS-300G-14PSW | CLI Manual - Page 73
    ,32,64,128,256,512> Policer rate (default fps) 3.10.3 qos cos Description Class of service configuration Syntax qos cos Parameter Name Description Specific class of service 3.10.4 qos dscp-classify Description Set qos dscp-classify. Syntax qos dscp-classify { zero | selected
  • D-Link DIS-300G-14PSW | CLI Manual - Page 74
    be af11~13 af22~23 af31~33 Af41~43 cs1~7 ef va Dscp level Default PHB(DSCP 0) for best effort traffic Assured Forwarding PHB 11~13(DSCP 10,12,14) Assured Forwarding PHB 22~23(DSCP 20,22) Assured Forwarding PHB 31~33(DSCP 26,28,30) Assured Forwarding PHB 41~43(DSCP 34,36,38) Class
  • D-Link DIS-300G-14PSW | CLI Manual - Page 75
    3.10.11 qos policer Description Syntax Parameter 3.10.12 qos wrr Description Syntax Parameter af11~13 af22~23 af31~33 Af41~43 cs1~7 ef va Assured Forwarding PHB 11~13(DSCP 10,12,14) Assured Forwarding PHB 22~23(DSCP 20,22) Assured Forwarding PHB 31~33(DSCP 26,28,30) Assured Forwarding PHB 41
  • D-Link DIS-300G-14PSW | CLI Manual - Page 76
    3.11 IGMP Functional Commands 3.11.1 ip igmp host-proxy [ leave-proxy ] Description IGMP proxy for leave configuration Syntax ip igmp host-proxy [ leave-proxy ] Parameter Name Description leave-proxy IGMP proxy for leave 3.11.2 ip igmp snooping Description Snooping igmp Syntax ip igmp
  • D-Link DIS-300G-14PSW | CLI Manual - Page 77
    3.11.9 ip igmp snooping vlan Description ipigmp snooping vlan IDs Syntax ip igmp snooping vlan Parameter Name Description vlan_list VLAN identifier(s): VID 3.11.10 ip igmp ssm-range Description SSM range Syntax ip igmp ssm-range Parameter
  • D-Link DIS-300G-14PSW | CLI Manual - Page 78
    priority CoS priority ranges from 0 to 7 3.12.5 mvr name frame tagged Description MVR control frame in TX, Tagged IGMP/MLD frames will be sent Syntax mvr name frame tagged Parameter Name Description name MVR multicast VLAN name 3.12.6 mvr name
  • D-Link DIS-300G-14PSW | CLI Manual - Page 79
    Parameter Name Description < vlan_list > MVR multicast VLAN list CoS priority ranges from 0 to 7 3.12.13 mvr vlan frame tagged Description Set tagged IGMP/MLD frames will be sent Syntax mvr vlan frame tagged Parameter Name Description < vlan_list > MVR
  • D-Link DIS-300G-14PSW | CLI Manual - Page 80
    auto Compatible with MLDv1/MLDv2 v1 Forced MLDv1 v2 Forced MLDv2 3.13.4 ipv6 mld snooping immediate-leave Description IPv6 MLD snooping immediate-leave configuration Syntax ipv6 mld snooping immediate-leave Parameter 3.13.5 ipv6 mld snooping last-member-query-interval Description ipv6
  • D-Link DIS-300G-14PSW | CLI Manual - Page 81
    Name Description v_ipv6_mcast Valid IPv6 multicast address ipv6_prefix_length length 3.13.12 ipv6 mld unknown-flooding Description Flooding unregistered IPv6 multicast traffic Syntax ipv6 mld unknown-flooding Parameter 3.13.13 ipv6 route Description Syntax Parameter IPv6 Route ipv6 route
  • D-Link DIS-300G-14PSW | CLI Manual - Page 82
    Syntax Parameter radius-server host [ auth-port ] [ acct-port ] [ timeout ] [ retransmit ] [ key ] Name auth-port acct-port timeout retransmit Description Hostname or IP address UDP port
  • D-Link DIS-300G-14PSW | CLI Manual - Page 83
    3.14.11 tacacs-server deadtime Description Time to stop using a TACACS+ server that doesn't respond Syntax tacacs-server deadtime Parameter Name Description < Time in minutes 3.14.12 tacacs-server deadtime Description Time to stop using a TACACS+ server
  • D-Link DIS-300G-14PSW | CLI Manual - Page 84
    Parameter 3.14.18 dot1x timeout Description Timeout control Syntax dot1x timeout { quiet-period } | { tx-period
  • D-Link DIS-300G-14PSW | CLI Manual - Page 85
    Name [ statistics ] Description Count radius packet statistics 3.14.24 enable Description Syntax Parameter 3.14.25 end Description Syntax Parameter 3.14.26 exit Description Syntax Parameter 3.14.27 hostname Description Syntax Parameter Privilege level control Enable { password [ level ] <
  • D-Link DIS-300G-14PSW | CLI Manual - Page 86
    Syntax Parameter loop-protect transmit-time Name 1-10 Description Transmit time in second 3.15.5 loop-protect tx-mode Description Loop protection actively generate PDUs Syntax loop-protect tx-mode Parameter 3.16 LLDP Configure commands 3.16.1 lldp holdtime Description Syntax
  • D-Link DIS-300G-14PSW | CLI Manual - Page 87
    3.16.3 lldp receive Description Syntax : Policy id for the policy which is created Enable/Disable decoding of received LLDP frames. lldp receive 3.16.4 lldp reinit Description LLDP tx reinitialization delay in seconds. Syntax lldp reinit Parameter Name
  • D-Link DIS-300G-14PSW | CLI Manual - Page 88
    Parameter 3.17 RFC2544 Testing Configure Commands 3.17.1 rfc2544 profile Description RFC2544 profile configuration Syntax rfc2544 profile Parameter Name Description Profile name up to 32 characters long 3.17.2 rfc2544 rename profile Description Rename an
  • D-Link DIS-300G-14PSW | CLI Manual - Page 89
    3.18 GVRP Configure Commands 3.18.1 gvrp Description Syntax Parameter Enable GVRP on port(s) gvrp 3.18.2 gvrpjoin request vlan Description Emit a Join-Request for test purpose Syntax gvrp join-request vlan Parameter Name Description vlan_list List of VLANs 3.18.3 gvrpleave
  • D-Link DIS-300G-14PSW | CLI Manual - Page 90
    Profile alarm profile alarm 3.20.2 alarm Description Syntax Parameter Set alarm content alarm { mask | unmask | major | minor } 101~114: GE-1~14 Port link down (for 14 port model) Name Description alarmId 151: set Power alarm mask unmask major minor Set alarm as mask, it means event
  • D-Link DIS-300G-14PSW | CLI Manual - Page 91
    Parameter Name allocation-consumption allocation-reserved-power class-consumption class-reserved-power lldp-consumption lldp-reserved-power Description Max. port power determined by allocated, and power is managed according to power consumption. Max. port power determined by allocated, and power
  • D-Link DIS-300G-14PSW | CLI Manual - Page 92
    3.21.6 poe power Description Syntax Parameter 3.21.7 poe priority Description Syntax Parameter at Set operation mode to 802.3at(Maximum power 30.0 W) Set maximum power for port in allocation mode. poe power limit Name Description Maximum power for the interface (0-15.4 Watt for
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
DIS-300G Series
Industrial Managed Ethernet Switch
CLI Reference Guide
Rev 0.1