D-Link DXS-3600-EM-4QXS Hardware Installation Guide - Page 26

Configuring the IP Address, Privileged EXEC Mode

Get D-Link DXS-3600-EM-4QXS PDF manuals and user guides View all D-Link DXS-3600-EM-4QXS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

DXS-3600-32S 10GbE Layer 2/3 Switch Hardware Installation Guide DXS-3600-32S>enable DXS-3600-32S#configure terminal DXS-3600-32S(config)#username NewUser password 12345 DXS-3600-32S(config)#username NewUser privilege 15 DXS-3600-32S(config)#line console DXS-3600-32S(config-line)#login local DXS-3600-32S(config-line)#end DXS-3600-32S# Figure 4-5 To create a user account 1 At the CLI command prompt, enter the command 'enable' to enter the Privileged EXEC Mode. Press Enter. 2 Enter the command 'configure terminal' to enter the Global Configuration Mode. Press Enter. 3 Enter the command 'username NewUser password 12345'. Press Enter. This will create a user account with the username of 'NewUser' and a password of '12345'. 4 Enter the command 'username NewUser privilege 15'. Press Enter. This will configure this user account to have Administrative (15) privileges. 5 Enter the command 'line console' to enter the Line Configuration Mode. Press Enter. 6 Enter the command 'login local'. Press Enter. This specifies that the local line requires login credentials. 7 Enter the command 'end' to exit back to the Privileged EXEC Mode. NOTE: Passwords are case sensitive. Usernames and passwords can be up to 15 characters in length. Configuring the IP Address Each switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or other TCP/IP applications. The switch's default IP address is 0.0.0.0 and should thus be configured prior to installation. You can change the switch's default IP address to fit into your networking address range. The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be found by entering the command "show system-info" into the command line interface in the Privileged EXEC mode, as shown below. DXS-3600-32S>enable DXS-3600-32S#show system-info Device Type MAC Address IP Address VLAN Name Subnet Mask Default Gateway Boot PROM Version Firmware Version Hardware Version Firmware Type Serial Number System Name System Location System Uptime System Contact : DXS-3600 TenGigabit Ethernet Switch : 00-01-02-03-04-00 : 0.0.0.0 (Manual) : default : 0.0.0.0 : 0.0.0.0 : Build 1.00.007 : Build 1.00.024 : : EI : D1234567890 : : : 0 days, 0 hours, 20 minutes, 59 seconds : DXS-3600-32S# Figure 4-6 The 'show system-info' command 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
DXS-3600-32S 10GbE Layer 2/3 Switch Hardware Installation Guide
19
Figure 4-5 To create a user account
1 At the CLI command prompt, enter the command ‘
enable
’ to enter the
Privileged EXEC Mode
. Press
Enter
.
2 Enter the command ‘
configure terminal
’ to enter the
Global Configuration Mode
. Press
Enter
.
3 Enter the command ‘
username NewUser password 12345
’. Press
Enter
. This will create a user account with the
username of ‘NewUser’ and a password of ‘12345’.
4 Enter the command ‘
username NewUser privilege 15
’. Press
Enter
. This will configure this user account to have
Administrative
(
15
) privileges.
5 Enter the command ‘
line console
’ to enter the
Line Configuration Mode
. Press
Enter
.
6 Enter the command ‘
login local
’. Press
Enter
. This specifies that the local line requires login credentials.
7 Enter the command ‘
end
’ to exit back to the
Privileged EXEC Mode
.
Configuring the IP Address
Each switch must be assigned its own IP Address, which is used for communication with an SNMP network manager
or other TCP/IP applications. The switch's default IP address is
0.0.0.0
and should thus be configured prior to
installation. You can change the switch’s default IP address to fit into your networking address range.
The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be
found by entering the command "
show system-info
" into the command line interface in the
Privileged EXEC
mode,
as shown below.
Figure 4-6 The ‘show system-info’ command
DXS-3600-32S>enable
DXS-3600-32S#configure terminal
DXS-3600-32S(config)#username NewUser password 12345
DXS-3600-32S(config)#username NewUser privilege 15
DXS-3600-32S(config)#line console
DXS-3600-32S(config-line)#login local
DXS-3600-32S(config-line)#end
DXS-3600-32S#
NOTE:
Passwords are case sensitive. Usernames and passwords can be up to 15 characters in
length.
DXS-3600-32S>enable
DXS-3600-32S#show system-info
Device Type
: DXS-3600 TenGigabit Ethernet Switch
MAC Address
: 00-01-02-03-04-00
IP Address
: 0.0.0.0 (Manual)
VLAN Name
: default
Subnet Mask
: 0.0.0.0
Default Gateway
: 0.0.0.0
Boot PROM Version
: Build 1.00.007
Firmware Version
: Build 1.00.024
Hardware Version
:
Firmware Type
: EI
Serial Number
: D1234567890
System Name
:
System Location
:
System Uptime
: 0 days, 0 hours, 20 minutes, 59 seconds
System Contact
:
DXS-3600-32S#