Dell 2355dn Multifunction Mono Laser Printer Wireless and Network Guide - Page 58

Appendix I. Regulatory statement, FCC Compliance, FCC Statement, Caution, RF-exposure statement - emissions

Get Dell 2355dn Multifunction Mono Laser Printer PDF manuals and user guides View all Dell 2355dn Multifunction Mono Laser Printer manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Appendix I. Regulatory statement FCC Compliance FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications NOT explicitly APPROVED by Samsung Electronics Co., Ltd. the responsible for complaince could cause the DELL5002 module to cease to comply with FCC rules part 15, and thus void the user's authority to operate the equipment. RF-exposure statement These modular transmitters, DELL5002, comply with FCC radiation exposure limits set forth for an uncontrolled environment. The DELL5002 should be installed and operated with minimum distance 20cm between the antenna and the body of the user or nearby persons. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrate this module. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Appendix I. Regulatory statement 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Appendix I. Regulatory statement
56
Appendix I. Regulatory statement
FCC Compliance
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution
Any changes or modifications NOT explicitly APPROVED by Samsung
Electronics Co., Ltd. the responsible for complaince could cause the
DELL5002 module to cease to comply with FCC rules part 15, and thus void
the user's authority to operate the equipment.
RF-exposure statement
These modular transmitters, DELL5002, comply with FCC radiation
exposure limits set forth for an uncontrolled environment. The DELL5002
should be installed and operated with minimum distance 20cm between the
antenna and the body of the user or nearby persons.
The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the user’s manual
of the end product which integrate this module.
This device is intended only for OEM integrators under the following
conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and 2) The transmitter module may not be co-located
with any other transmitter or antenna.
As long as the 2 conditions above are met, further transmitter testing will not
be required. However, the OEM integrator is still responsible for testing their
end product for any additional compliance requirements required with this
module installed (for example, digital device emissions, PC peripheral
requirements, etc.).