Dell Dimension 5150 Service Manual - Page 41

Diskette Drive, To connect a network cable - fan

Get Dell Dimension 5150 PDF manuals and user guides View all Dell Dimension 5150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

2 screws (4) 1. Follow the procedures in "Before You Begin." 2. Remove the computer cover. 3. Remove the drive panel. NOTE: If you are installing a new drive, you need to remove the drive-panel insert. 4. Slide the drive into place until you feel a click or feel the drive securely installed. 5. Attach the power and data cables to the floppy drive. 6. Connect the other end of the data cable to the connector labeled "DSKT" on the system board and route the cable through the clip on the shroud. 1 power cable 2 data cable 7. Check all cable connections and fold cables out of the way to avoid blocking the fan and cooling vents. 8. Replace the drive panel. 9. Replace the computer cover. NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer. 10. Connect your computer and devices to their electrical outlets, and turn them on. See the documentation that came with the drive for instructions on installing any software required for drive operation. 11. Enter system setup and select the appropriate Diskette Drive option. 12. Verify that your computer works correctly by running the Dell Diagnostics.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
2
screws (4)
1. Follow the procedures in "
Before You Begin
."
2. Remove the computer cover.
3. Remove the
drive panel
.
NOTE:
If you are installing a new drive, you need to remove the
drive-panel insert
.
4. Slide the drive into place until you feel a click or feel the drive securely installed.
5. Attach the power and data cables to the floppy drive.
6. Connect the other end of the data cable to the connector labeled "DSKT" on the system board and route the cable
through the clip on the shroud.
1
power cable
2
data cable
7. Check all cable connections and fold cables out of the way to avoid blocking the fan and cooling vents.
8. Replace the
drive panel
.
9. Replace the
computer cover
.
NOTICE:
To connect a network cable, first plug the cable into the network port or device and then plug it into the
computer.
10. Connect your computer and devices to their electrical outlets, and turn them on.
See the documentation that came with the drive for instructions on installing any software required for drive operation.
11. Enter system setup and select the appropriate
Diskette Drive
option.
12. Verify that your computer works correctly by running the
Dell Diagnostics
.