Dell Dimension E310 Owner's Manual - Page 87

Installing a Floppy Drive, the back of the drive panel insert to the drive see

Get Dell Dimension E310 PDF manuals and user guides View all Dell Dimension E310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Installing a Floppy Drive NOTE: In the event that the replacement or new floppy drive does not have the shoulder screws, use the screws located within the drive panel insert. drive screws (4) 1 Follow the procedures in "Before You Begin" on page 57. 2 Remove the drive panel (see page 74). 3 If you are installing a new floppy drive rather than replacing a drive, remove the drive panel insert where you want the drive to be installed, and then attach the shoulder screws located in the back of the drive panel insert to the drive (see page 75). 4 Gently slide the drive into place until you hear a click or feel the drive securely installed. 5 Attach the power and data cables to the floppy drive. 6 Connect the other end of the data cable to the connector labeled "FLOPPY" on the system board (see page 65) and route the cable through the clip on the shroud. Removing and Installing Parts 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Removing and Installing Parts
85
Installing a Floppy Drive
NOTE:
In the event that the replacement or new floppy drive does not have the shoulder screws, use the
screws located within the drive panel insert.
1
Follow the procedures in "Before You Begin" on page57.
2
Remove the drive panel (see page 74).
3
If you are installing a new floppy drive rather than replacing a drive, remove the drive panel
insert where you want the drive to be installed, and then attach the shoulder screws located in
the back of the drive panel insert to the drive (see page 75).
4
Gently slide the drive into place until you hear a click or feel the drive securely installed.
5
Attach the power and data cables to the floppy drive.
6
Connect the other end of the data cable to the connector labeled "FLOPPY" on the system
board (see page 65) and route the cable through the clip on the shroud.
drive
screws (4)