Dell Force10 Software Defined Networking Software-Defined Networking (SDN) Dep - Page 17

Learning Bridge (LB) Flows, Packet Trace, Instance: 2, Table: lb, Flow: 5, Cookie: 0xfac2dbc22

Get Dell Force10 Software Defined Networking PDF manuals and user guides View all Dell Force10 Software Defined Networking manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Idle Timeout: 0 seconds, Internal Idle Timeout: 0 seconds Packets: -, Bytes: - Match Parameters: Valid Match: DMAC,Vid In Port : * EType : * SMAC : * DMAC : 00:22:22:22:22:22 VLAN id : 200 VLAN PCP : * IP TOS : * IP proto : * Src IP : * Dest IP : * Src Port : * Dest Port : * Actions: Output: Te 0/1 For complete L2 flow formats, refer to FlowTypes . Learning Bridge (LB) Flows Learning bridge flows are only supported on OF VLANs. In the example below, of-instance 2 represents an LB flow. To use the LB flow table, you must enable the multiple-fwd-table and learning-switch-assist commands, as shown below. If you do not enable either command, LB flows are added to the ACL table. FTOS#show running-config openflow of-instance 2 ! openflow of-instance 2 controller 1 10.11.205.184 tcp flow-map l2 enable flow-map l3 enable interface-type vlan learning-switch-assist enable multiple-fwd-table enable no shutdown The example below shows a sample flow in of-vlan 200: FTOS#show openflow flows of-instance 2 Instance: 2, Table: lb, Flow: 5, Cookie: 0xffffffffac2dbc22 Priority: 32768, Internal Priority: 0 Up Time: 0d 00:00:03, Hard Timeout: 0 seconds Idle Timeout: 0 seconds, Internal Idle Timeout: 0 seconds Packets: -, Bytes: - Match Parameters: Valid Match: InPort,SMAC,DMAC,Vid In Port : Te 0/0 EType : * SMAC : 00:00:00:00:00:11 DMAC : 00:00:00:00:00:33 VLAN id : 200 VLAN PCP : * IP TOS : * IP proto : * Src IP : * Dest IP : * Src Port : * Dest Port : * Actions: Output: Te 0/1 For complete LB flow formats, refer to FlowTypes . Packet Trace Enable OpenFlow protocol packet tracing by using the debug openflow packets packet-type {of-id} command. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
Idle Timeout: 0 seconds, Internal Idle Timeout: 0 seconds
Packets: -, Bytes: -
Match Parameters:
Valid Match: DMAC,Vid
In Port
: *
EType
: *
SMAC
: *
DMAC
: 00:22:22:22:22:22
VLAN id
: 200
VLAN PCP
: *
IP TOS
: *
IP proto
: *
Src IP
: *
Dest IP
: *
Src Port
: *
Dest Port : *
Actions:
Output: Te 0/1
For complete L2 flow formats, refer to
FlowTypes
.
Learning Bridge (LB) Flows
Learning bridge flows are only supported on OF VLANs. In the example below, of-instance 2 represents an LB flow. To
use the LB flow table, you must enable the
multiple-fwd-table
and
learning-switch-assist
commands,
as shown below. If you do not enable either command, LB flows are added to the ACL table.
FTOS#show running-config openflow of-instance 2
!
openflow of-instance 2
controller 1 10.11.205.184 tcp
flow-map l2 enable
flow-map l3 enable
interface-type vlan
learning-switch-assist enable
multiple-fwd-table enable
no shutdown
The example below shows a sample flow in of-vlan 200:
FTOS#show openflow flows of-instance 2
Instance: 2, Table: lb, Flow: 5, Cookie: 0xffffffffac2dbc22
Priority: 32768, Internal Priority: 0
Up Time: 0d 00:00:03, Hard Timeout: 0 seconds
Idle Timeout: 0 seconds, Internal Idle Timeout: 0 seconds
Packets: -, Bytes: -
Match Parameters:
Valid Match: InPort,SMAC,DMAC,Vid
In Port
: Te 0/0
EType
: *
SMAC
: 00:00:00:00:00:11
DMAC
: 00:00:00:00:00:33
VLAN id
: 200
VLAN PCP
: *
IP TOS
: *
IP proto
: *
Src IP
: *
Dest IP
: *
Src Port
: *
Dest Port : *
Actions:
Output: Te 0/1
For complete LB flow formats, refer to
FlowTypes
.
Packet Trace
Enable OpenFlow protocol packet tracing by using the
debug openflow packets packet-type {
of-id
}
command.
17