Dell Inspiron 3670 Service Manual - Page 55

Replacing the system board, Procedure

Get Dell Inspiron 3670 PDF manuals and user guides View all Dell Inspiron 3670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

33 Replacing the system board WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You must make the appropriate changes again after you replace the system board. Topics: • Procedure • Post-requisites Procedure NOTE: To ensure that cables are connected to the correct system board connectors, see "System board components'. NOTE: Depending on the configuration ordered your computer may have up to two 2.5-inch hard-drives installed. If only one hard-drive is installed skip step 9 or step 11 where applicable. 1 Slide the edge of the system board into the front-I/O slot on the chassis and lower the system board into the chassis. 2 Align the screw holes on the system board with the screw holes on the on the chassis. Replacing the system board 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Replacing the system board
WARNING:
Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After working inside
your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/
regulatory_compliance
.
NOTE:
Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program
after you replace the system board.
NOTE:
Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You must
make the appropriate changes again after you replace the system board.
Topics:
•
Procedure
•
Post-requisites
Procedure
NOTE:
To ensure that cables are connected to the correct system board connectors, see “
System board components
’.
NOTE:
Depending on the
configuration
ordered your computer may have up to two 2.5-inch hard-drives installed. If only one
hard-drive is installed skip step 9 or step 11 where applicable.
1
Slide the edge of the system board into the front-I/O slot on the chassis and lower the system board into the chassis.
2
Align the screw holes on the system board with the screw holes on the on the chassis.
33
Replacing the system board
55