Dell Latitude 7480 Owners Manual - Page 30

Removing display assembly—with Touch

Get Dell Latitude 7480 PDF manuals and user guides View all Dell Latitude 7480 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Removing display assembly-with Touch 1 Follow the procedure in Before working inside your computer. 2 Remove the: a base cover b battery c WLAN card d WWAN card NOTE: To identify the number of screws, see screw list 3 To remove the display assembly: a Un route the WLAN and WWAN cables from the routing channels [1]. b Disconnect the IR camera cable from the system board [2]. c Remove the M2.0x3.0 screws that secures the eDP bracket [3]. d Lift the eDP bracket from the eDP cable [4]. e Lift the eDP cable to disconnect it from the connector on the system board [5]. f Un route the eDP cable from the routing channel [6]. 4 To remove the display assembly: a Open the display of the computer and lay it on a flat surface at 180 degree angle b Remove the M2.5 x 4.0 screws that secure the display hinge to the display assembly [1]. c Lift the display assembly from the computer. 30 Disassembly and reassembly

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Removing display assembly—with Touch
1
Follow the procedure in
Before working inside your computer
.
2
Remove the:
a
base cover
b
battery
c
WLAN card
d
WWAN card
NOTE:
To identify the number of screws, see
screw list
3
To remove the display assembly:
a
Un route the WLAN and WWAN cables from the routing channels [1].
b
Disconnect the IR camera cable from the system board [2].
c
Remove the M2.0x3.0 screws that secures the eDP bracket [3].
d
Lift the eDP bracket from the eDP cable [4].
e
Lift the eDP cable to disconnect it from the connector on the system board [5].
f
Un route the eDP cable from the routing channel [6].
4
To remove the display assembly:
a
Open the display of the computer and lay it on a
flat
surface at 180 degree angle
b
Remove the M2.5 x 4.0 screws that secure the display hinge to the display assembly [1].
c
Lift the display assembly from the computer.
30
Disassembly and reassembly