Dell PowerConnect Brocade 6505 Hardware Reference Guide - Page 39

Removal and Replacement of Power Supplies and Fans, In this Introduction

Get Dell PowerConnect Brocade 6505 PDF manuals and user guides View all Dell PowerConnect Brocade 6505 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Chapter 4 Removal and Replacement of Power Supplies and Fans In this chapter •Introduction 27 •Removing and replacing a power supply and fan assembly 27 Introduction NOTE Read the "Installation and safety considerations" on page 5 before servicing. The field-replaceable units (FRUs) in the Brocade 6505 can be removed and replaced without special tools. The Brocade 6505 can continue operating during the FRU replacement if the conditions specified in the procedure are followed. Removing and replacing a power supply and fan assembly The Brocade 6505 fans are fixed inside the combined power supply and fan assembly to provide necessary airflow to cool the entire system. There are two fans located in each power supply and fan assembly. The system software sets fan speed and measures the speed through the tachometer interface. The base model Brocade 6505 has one power supply and fan assembly, as displayed in Figure 7. Fabric OS identifies the assemblies from right to left on the nonport side. Even though they are contained within a single unit, the power supply and fan components are identified separately. In the chassisShow command they are identified as Power Supply Unit:1 and Fan Unit:1. Brocade 6505 Hardware Reference Manual 27 53-1002449-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Brocade 6505 Hardware Reference Manual
27
53-1002449-01
Chapter
4
Removal and Replacement of Power Supplies and Fans
In this chapter
•
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
•
Removing and replacing a power supply and fan assembly. . . . . . . . . . . . .
27
Introduction
NOTE
Read the
“Installation and safety considerations”
on page 5 before servicing.
The field-replaceable units (FRUs) in the Brocade 6505 can be removed and replaced without
special tools. The Brocade 6505 can continue operating during the FRU replacement if the
conditions specified in the procedure are followed.
Removing and replacing a power supply and fan assembly
The Brocade 6505 fans are fixed inside the combined power supply and fan assembly to provide
necessary airflow to cool the entire system. There are two fans located in each power supply and
fan assembly. The system software sets fan speed and measures the speed through the
tachometer interface.
The base model Brocade 6505 has one power supply and fan assembly, as displayed in
Figure 7
.
Fabric OS identifies the assemblies from right to left on the nonport side. Even though they are
contained within a single unit, the power supply and fan components are identified separately. In
the
chassisShow
command they are identified as Power Supply Unit:1 and Fan Unit:1.