Dell PowerEdge 1750 Information Update (.pdf) - Page 9

Replace the SCSI backplane. See Installation and Troubleshooting Guide - hard drive

Get Dell PowerEdge 1750 PDF manuals and user guides View all Dell PowerEdge 1750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Figure 1-4. Installing the ERA/O Card ERA/O card ERA/O card connector retention clips (4) 10 If you removed a ROMB backup battery in step 7, replace the battery. See Figure 1-3; also see "Installing a ROMB Card" in your Installation and Troubleshooting Guide. 11 Replace the SCSI backplane. See Figure 1-2. a Fit the metal tabs at each end of the backplane into the slots in the chassis wall, and lower the backplane into the chassis, ensuring that the CD and diskette drive interface cables are not caught under the backplane. b Press down firmly over the handle to seat the backplane in its connector. c Pivot the release latch out into the securing slot in the chassis. d Connect the CD drive interface cable to the CD_ROM connector on the backplane board. e Connect the diskette-drive interface cable to the FLOPPY connector on the backplane board. f Press all installed hard drives firmly back into the SCSI connectors on the backplane. 12 Close the system covers. When closing the covers, close the right (larger) cover first and then close the left cover. Press firmly on the left cover to snap the securing latch into place. 13 Install the optional security screw (if applicable). See Figure 1-1. Installing or Replacing an ERA/O Card 1-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Installing or Replacing an ERA/O Card
1-5
Figure 1-4.
Installing the ERA/O Card
10
If you removed a ROMB backup battery in step 7, replace the battery. See Figure 1-3;
also see "Installing a ROMB Card" in your
Installation and Troubleshooting Guide
.
11
Replace the SCSI backplane. See Figure 1-2.
a
Fit the metal tabs at each end of the backplane into the slots in the chassis wall,
and lower the backplane into the chassis, ensuring that the CD and diskette drive
interface cables are not caught under the backplane.
b
Press down firmly over the handle to seat the backplane in its connector.
c
Pivot the release latch out into the securing slot in the chassis.
d
Connect the CD drive interface cable to the CD_ROM connector on the
backplane board.
e
Connect the diskette-drive interface cable to the FLOPPY connector on the
backplane board.
f
Press all installed hard drives firmly back into the SCSI connectors on the
backplane.
12
Close the system covers.
When closing the covers, close the right (larger) cover first and then close the left
cover. Press firmly on the left cover to snap the securing latch into place.
13
Install the optional security screw (if applicable). See Figure 1-1.
ERA/O card
retention clips (4)
ERA/O card connector