Dell PowerEdge M520 Rack Installation Guide - Page 16

Installing the RapidRails Assemblies

Get Dell PowerEdge M520 PDF manuals and user guides View all Dell PowerEdge M520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Installing the RapidRails Assemblies 1 At the front of the rack cabinet, position one of the RapidRails assemblies so that its mounting-bracket flange fits in the appropriate location on the rack (see Figure 1-5). The lower mounting tab on the rail assembly's front-mounting bracket flange should enter the tenth hole up from the lower mark on the vertical rails (see Figure 1-5). 2 Push the rail assembly forward until the top mounting tab enters the square hole, which is located 4-U spaces below the upper marks or tape you placed on the vertical rail (see Figure 1-5). 3 Next, push down on the mounting-bracket flange until the mounting tabs seat in the square holes and the push button pops out and clicks (see Figure 1-5). 4 At the back of the cabinet, pull back on the mounting-bracket flange until the mounting tabs are in the appropriate holes, and then push down on the flange until the mounting tabs seat in the square holes and the push button pops out and clicks. 5 Repeat step 1 through step 4 for the rail assembly on the other side of the rack. NOTE: Ensure that the rails are mounted at the same vertical position on both sides of the rack. 14 Rack Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
14
Rack Installation Guide
Installing the RapidRails Assemblies
1
At the front of the rack cabinet, position one of the RapidRails assemblies
so that its mounting-bracket flange fits in the appropriate location on the
rack (see Figure 1-5).
The lower mounting tab on the rail assembly’s front-mounting bracket
flange should enter the tenth hole up from the lower mark on the vertical
rails (see Figure 1-5).
2
Push the rail assembly forward until the top mounting tab enters the
square hole, which is located 4-U spaces below the upper marks or tape
you placed on the vertical rail (see Figure 1-5).
3
Next, push down on the mounting-bracket flange until the mounting tabs
seat in the square holes and the push button pops out and clicks
(see Figure 1-5).
4
At the back of the cabinet, pull back on the mounting-bracket flange until
the mounting tabs are in the appropriate holes, and then push down on
the flange until the mounting tabs seat in the square holes and the push
button pops out and clicks.
5
Repeat step 1 through step 4 for the rail assembly on the other side
of the rack.
NOTE:
Ensure that the rails are mounted at the same vertical position on both
sides of the rack.