Dell PowerVault 122T LTO Dell PowerVault 122T LTO Autoloader User's Guide - Page 19

Autoloader Error Codes - 2 display messages

Get Dell PowerVault 122T LTO PDF manuals and user guides View all Dell PowerVault 122T LTO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

10. After removing the cartridges from the desired carriers, reinstall each carrier on the autoloader belt (see Installing the Carrier). 11. Make sure that the rollers on the bottom of the carrier are aligned in the carrier tracks. 12. Make sure that the belt post beneath each carrier are inserted into the proper autoloader belt loop. NOTE: There are unused loops on the belt. The proper belt loops have an extra bump on the outside of the loop. (see "Installing the Carrier"). Installing the Carrier 13. Insert the peg on the bottom of the cartridge carrier into the slot in the belt, then gently turn the cartridge carrier in place to lock it in the belt. 14. Ensure the carrier is properly installed on the belt by gently pressing on the top of the carrier and sliding it back and forth. If it is properly attached to the belt, it should not move. If it does, reinstall the carrier. 15. Replace the top cover of the autoloader and reinstall the cover screws and mounting brackets (if rack mounted). Autoloader Error Codes If an error occurs during operation of the autoloader, the autoloader stops the current operation and displays an error code on the top line of the LCD screen. Unless otherwise noted in "Autoloader Error Codes," attempt to resolve the error by resetting or power cycling the autoloader and retrying the last operation. If the error persists, contact Dell. To view the error log follow these steps: 1. From the Home screen or main menu, press + or - until Information appears on the top line of the LCD screen. 2. Press Enter to access the available options. 3. Press + or - until View Error Log appears on the LCD screen. The LCD screen also displays the quantity of errors and events currently stored in the error log. 4. Press Enter to access the most recently logged error message. 5. Press + or - to display each error in the log. 6. Press Cancel when finished. A description of each of the error codes is provided in the following table: NOTE: Error codes displayed on the front panel LCD during normal operation, as opposed to when viewing them through the event log, will not display the preceding '3' and '0' characters, included in the table below. Also note that when viewing the event log, error codes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
10.
After removing the cartridges from the desired carriers, reinstall each carrier on the autoloader belt (see
Installing the Carrier
).
11.
Make sure that the rollers on the bottom of the carrier are aligned in the carrier tracks.
12.
Make sure that the belt post beneath each carrier are inserted into the proper autoloader belt loop.
Installing the Carrier
13.
Insert the peg on the bottom of the cartridge carrier into the slot in the belt, then gently turn the cartridge carrier in place to lock it in the belt.
14.
Ensure the carrier is properly installed on the belt by gently pressing on the top of the carrier and sliding it back and forth. If it is properly attached to
the belt, it should not move. If it does, reinstall the carrier.
15.
Replace the top cover of the autoloader and reinstall the cover screws and mounting brackets (if rack mounted).
Autoloader Error Codes
If an error occurs during operation of the autoloader, the autoloader stops the current operation and displays an error code on the top line of the LCD screen.
Unless otherwise noted in "
Autoloader Error Codes
," attempt to resolve the error by resetting or power cycling the autoloader and retrying the last operation.
If the error persists,
contact
Dell.
To view the error log follow these steps:
1.
From the Home screen or main menu, press
+
or
-
until
Information
appears on the top line of the LCD screen.
2.
Press
Enter
to access the available options.
3.
Press
+
or
-
until
View Error Log
appears on the LCD screen.
The LCD screen also displays the quantity of errors and events currently stored in the error log.
4.
Press
Enter
to access the most recently logged error message.
5.
Press
+
or
-
to display each error in the log.
6.
Press
Cancel
when finished.
A description of each of the error codes is provided in the following table:
NOTE:
There are unused loops on the belt. The proper belt loops have an extra bump on the outside of the loop. (see "
Installing the
Carrier
").
NOTE:
Error codes displayed on the front panel LCD during normal operation, as opposed to when viewing them through the event log,
will not display the preceding '3' and '0' characters, included in the table below. Also note that when viewing the event log, error codes