Dell PowerVault 35F Dell PowerVault 35F Fibre Channel Bridge Rack Installation - Page 13

hinges into position.

Get Dell PowerVault 35F PDF manuals and user guides View all Dell PowerVault 35F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

2. Tighten the eight 10-32 x 1/2-inch screws that mount the outer slides to the rack. 3. Tighten the thumbscrews on the bezel to keep the bridge and slide assembly from sliding out of the rack. The thumbscrews pass through the holes in the rack and into the middle holes of the stationary brackets. 5HSODFLQJWKH'RRUVRQWKH5DFN Use the following procedure to replace the rack's front and back doors. :$51,1*7RSUHYHQWSHUVRQDOLQMXU\GXHWRWKHVL]HDQGZHLJKWRIWKH GRRUVQHYHUDWWHPSWWRUHSODFHWKHGRRUVE\\RXUVHOI 1. Lift the front door into position, and align the hinges with the holes in the rack as shown in Figure 1-2. 2. Slide the hinges into the holes in the rack until the hinge release levers lock the hinges into position. 3. Close the door latch by rotating the handle counterclockwise until it stops, push the handle in until it locks in position, and then slide the push-button cover down over the push button (see Figure 1-1). Repeat steps 1 through 3 to install the back door. Dell PowerVault 35F Fibre Channel Bridge Rack Installation Guide 1-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
Dell PowerVault 35F Fibre Channel Bridge Rack Installation Guide
1-9
2.
Tighten the eight 10-32 x 1/2-inch screws that mount the outer slides to the rack.
3.
Tighten the thumbscrews on the bezel to keep the bridge and slide assembly
from sliding out of the rack.
The thumbscrews pass through the holes in the rack and into the middle holes of
the stationary brackets.
5HSODFLQJ²WKH²’RRUV²RQ²WKH²5DFN
Use the following procedure to replace the rack’s front and back doors.
:$51,1*±²7R²SUHYHQW²SHUVRQDO²LQMXU\²GXH²WR²WKH²VL]H²DQG²ZHLJKW²RI²WKH²
GRRUVµ²QHYHU²DWWHPSW²WR²UHSODFH²WKH²GRRUV²E\²\RXUVHOI³²
1.
Lift the front door into position, and align the hinges with the holes in the rack as
shown in Figure 1-2.
2.
Slide the hinges into the holes in the rack until the hinge release levers lock the
hinges into position.
3.
Close the door latch by rotating the handle counterclockwise until it stops, push
the handle in until it locks in position, and then slide the push-button cover down
over the push button (see Figure 1-1).
Repeat steps 1 through 3 to install the back door.