Dell PowerVault Storage Area Network Owner's Manual - Page 50

Installing The Cable Retention Bracket, Expansion Cards And Expansion-Card Risers

Get Dell PowerVault Storage Area Network PDF manuals and user guides View all Dell PowerVault Storage Area Network manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Figure 21. Removing and Installing the Cable Retention Bracket 1. alignment pins (2) 2. tab 3. cable retention bracket Installing The Cable Retention Bracket CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet. 2. Open the system. 3. Using alignment pins as guide, slide the cable retention bracket along the chassis wall until the tab snaps into place. 4. Place all cables to be routed in the cable retention bracket. 5. Install the cooling shroud. 6. Close the system. 7. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. Expansion Cards And Expansion-Card Risers NOTE: A missing or an unsupported expansion-card riser logs an SEL event. It does not prevent your system from powering on and no BIOS POST message or F1/F2 pause is displayed. Expansion Card Installation Guidelines The DR4100 system supports six expansion cards. The following PCI Express Generation 3 expansion cards are supported: 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
Figure 21. Removing and Installing the Cable Retention Bracket
1. alignment pins (2)
2. tab
3. cable retention bracket
Installing The Cable Retention Bracket
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
1.
Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.
2.
Open the system.
3.
Using alignment pins as guide, slide the cable retention bracket along the chassis wall until the tab snaps into
place.
4.
Place all cables to be routed in the cable retention bracket.
5.
Install the cooling shroud.
6.
Close the system.
7.
Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.
Expansion Cards And Expansion-Card Risers
NOTE:
A missing or an unsupported expansion-card riser logs an SEL event. It does not prevent your system from
powering on and no BIOS POST message or F1/F2 pause is displayed.
Expansion Card Installation Guidelines
The DR4100 system supports six expansion cards.
The following PCI Express Generation 3 expansion cards are supported:
50