Dell Precision M70 Service Manual - Page 17

Display Bezel

Get Dell Precision M70 PDF manuals and user guides View all Dell Precision M70 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

1 display 2 pull-tab 3 display cable connector 4 antenna cable 5 computer base 6 system board connector for display cable Display Bezel CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the display assembly. 3. Use a plastic scribe to pry the six round display bumpers out of the screw holes located on the front of the bezel. Do not remove the oval bumpers. 4. Remove the six M2.5 x 5-mm screws located on the front of the bezel under the bumpers. NOTICE: Carefully separate the bezel from the top cover to avoid damage to the bezel. 5. Separate the bezel from the top cover by lifting the inside edge of the bezel away from the top cover. NOTE: You may need to use a plastic scribe to begin the separation. Pull the bezel from the top edge toward the center of the panel to open the snaps. Push the bezel on the sides and bottom away from the center of the panel to open the snaps. NOTICE: To avoid damaging the bezel, start pulling the bezel up near the bottom of the display (near the DELL™ logo) and work around the display and toward the latch release.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
Display Bezel
1.
Follow the instructions in "
Preparing to Work Inside the Computer
."
2.
Remove the
display assembly
.
3.
Use a plastic scribe to pry the six round display bumpers out of the screw holes located on the front of the bezel. Do not remove the oval bumpers.
4.
Remove the six M2.5 x 5-mm screws located on the front of the bezel under the bumpers.
5.
Separate the bezel from the top cover by lifting the inside edge of the bezel away from the top cover.
Pull the bezel from the top edge toward the center of the panel to open the snaps. Push the bezel on the sides and bottom away from the center of the
panel to open the snaps.
1
display
2
pull-tab
3
display cable connector
4
antenna cable
5
computer base
6
system board connector
for display cable
CAUTION:
Before performing the following procedures, read the safety instructions in your
Product Information Guide
.
NOTICE:
To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
NOTICE:
Carefully separate the bezel from the top cover to avoid damage to the bezel.
NOTE:
You may need to use a plastic scribe to begin the separation.
NOTICE:
To avoid damaging the bezel, start pulling the bezel up near the bottom of the display (near the DELL™ logo) and work around the display
and toward the latch release.