Dell S4148F-ON EMC PowerSwitch S4100–ON Series Installation Guide M - Page 21

Rack mounting, Switch ground, Fans and airflow, Power, Fan combinations

Get Dell S4148F-ON PDF manuals and user guides View all Dell S4148F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

The cabinet must meet minimum size requirements. Airflow must be in accordance with the Electronic Industries Alliance (EIA) standard. Ensure that there is a minimum of 5 inches (12.7 cm) between the intake and exhaust vents and the cabinet wall. Rack mounting When you prepare your equipment rack, ensure that the rack is grounded. Ground the equipment rack to the same ground point the power service in your area uses. The ground path must be permanent. Switch ground Dell EMC recommends grounding your switch. Use the S4100-ON Series switch in a CBN. NOTE: For AC-powered switches, although the third conductor of the AC power cord provides a ground path, Dell EMC recommends grounding your switch with a dedicated ground wire. NOTE: For DC-powered switches, the only way to safely ground your switch is to attach a dedicated ground wire. Fans and airflow The fans on the S4100-ON Series (S4128F-ON, S4148F-ON, S4148FE-ON, S4128T-ON, S4148T-ON, and S4148U-ON) support two airflow options: normal and reverse. Fan combinations Fan installation is done as part of the factory install based on SKU type. The S4100-ON Series has stock keeping units (SKUs) that support the following configurations: ● AC PSU with fan airflow from the I/O to the PSU-normal ● AC PSU with fan airflow from the PSU to the I/O-reverse ● DC fan unit with airflow from the I/O to the PSU-normal ● DC fan unit with airflow from the PSU to the I/O-reverse Be sure to order the fans suitable to support your site's ventilation. Use a single type of airflow fan in your switch. Do not mix reverse and normal airflows in a single switch. For proper ventilation, position the S4100-ON Series switch in an equipment rack or cabinet with a minimum of 5 inches (12.7 cm) of clearance around the exhaust vents. The fan speed varies based on internal temperature monitoring. The switch never intentionally turns off the fans. For more information, see Fans. Power Connect the switch to the applicable power source using the appropriate power cable. An AC power cable is included with each PSU. When installing AC or DC switches, follow the requirements of the National Electrical Code ANSI/NFPA 70, where applicable. The switch is powered-up when the power cable is connected between the switch and the power source. For more information, see Power supplies. CAUTION: Always disconnect the power cable before you service the power supply slots. The switch has multiple power cords. Before servicing, ensure all power cords are disconnected. CAUTION: On the AC switch, use the power supply cable as the main disconnect device. Ensure that the socket-outlet is located/installed near the equipment and is easily accessible. Site preparations 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
The cabinet must meet minimum size requirements. Airflow must be in accordance with the Electronic Industries Alliance (EIA)
standard. Ensure that there is a minimum of 5 inches (12.7 cm) between the intake and exhaust vents and the cabinet wall.
Rack mounting
When you prepare your equipment rack, ensure that the rack is grounded. Ground the equipment rack to the same ground point
the power service in your area uses. The ground path must be permanent.
Switch ground
Dell EMC recommends grounding your switch. Use the S4100–ON Series switch in a CBN.
NOTE:
For AC-powered switches, although the third conductor of the AC power cord provides a ground path, Dell EMC
recommends grounding your switch with a dedicated ground wire.
NOTE:
For DC-powered switches, the only way to safely ground your switch is to attach a dedicated ground wire.
Fans and airflow
The fans on the S4100–ON Series (S4128F-ON, S4148F-ON, S4148FE-ON, S4128T-ON, S4148T-ON, and S4148U-ON) support
two airflow options: normal and reverse.
Fan combinations
Fan installation is done as part of the factory install based on SKU type. The S4100–ON Series has stock keeping units (SKUs)
that support the following configurations:
●
AC PSU with fan airflow from the I/O to the PSU—normal
●
AC PSU with fan airflow from the PSU to the I/O—reverse
●
DC fan unit with airflow from the I/O to the PSU—normal
●
DC fan unit with airflow from the PSU to the I/O—reverse
Be sure to order the fans suitable to support your site’s ventilation. Use a single type of airflow fan in your switch. Do not mix
reverse and normal airflows in a single switch.
For proper ventilation, position the S4100–ON Series switch in an equipment rack or cabinet with a minimum of 5 inches (12.7
cm) of clearance around the exhaust vents. The fan speed varies based on internal temperature monitoring. The switch never
intentionally turns off the fans.
For more information, see
Fans
.
Power
Connect the switch to the applicable power source using the appropriate power cable. An AC power cable is included with each
PSU.
When installing AC or DC switches, follow the requirements of the National Electrical Code ANSI/NFPA 70, where applicable.
The switch is powered-up when the power cable is connected between the switch and the power source.
For more information, see
Power supplies
.
CAUTION:
Always disconnect the power cable before you service the power supply slots. The switch has
multiple power cords. Before servicing, ensure all power cords are disconnected.
CAUTION:
On the AC switch, use the power supply cable as the main disconnect device. Ensure that the
socket-outlet is located/installed near the equipment and is easily accessible.
Site preparations
21