Dell S5232F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 32

S5148F-ON

Get Dell S5232F-ON PDF manuals and user guides View all Dell S5232F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Note: The commands in the tables below should be entered in the order shown. All commands are provided in the file attachment named S5148F-single-switch.txt. 7.3.1 General settings Configure the hostname, OOB management IP address and default gateway. Specify an NTP server accessible by the switch. In this example, this is an NTP server on the OOB management network, with a different IP address than that used by the VxRail nodes on the in-band management network. Enable RSTP as a precaution against loops. Note: In OS10EE, LLDP is enabled on each interface and globally by default. LLDP is useful for troubleshooting and validation. Dell EMC recommends leaving it enabled. General settings - single switch S5148F-ON configure terminal hostname S5148F-ON interface mgmt1/1/1 no ip address ip address 100.67.172.38/24 no shutdown management route 0.0.0.0/0 100.67.172.254 ntp server 100.67.10.20 spanning-tree mode rstp 7.3.2 Configure VLANs In this section, VLANs are configured per Table 2. Create the in-band management VLAN and assign an IP address. Create the vMotion, vSAN, and VM Network VLANs. Configure VLANs - single switch S5148F-ON interface vlan1611 description InBand_Mgmt ip address 172.16.11.254/24 no shutdown interface vlan1612 description vMotion no shutdown interface vlan1613 description vSAN no shutdown interface vlan1614 32 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON, S5232F-ON and S5148F-ON

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
32
Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON,
S5232F-ON and S5148F-ON
Note:
The commands in the tables below should be entered in the order shown. All commands are provided
in the file attachment named S5148F-single-switch.txt.
7.3.1
General settings
Configure the hostname, OOB management IP address and default gateway. Specify an NTP server
accessible by the switch. In this example, this is an NTP server on the OOB management network, with a
different IP address than that used by the VxRail nodes on the in-band management network. Enable RSTP
as a precaution against loops.
Note:
In OS10EE, LLDP is enabled on each interface and globally by default. LLDP is useful for
troubleshooting and validation. Dell EMC recommends leaving it enabled.
General settings – single switch
S5148F-ON
configure terminal
hostname S5148F-ON
interface mgmt1/1/1
no ip address
ip address 100.67.172.38/24
no shutdown
management route 0.0.0.0/0 100.67.172.254
ntp server 100.67.10.20
spanning-tree mode rstp
7.3.2
Configure VLANs
In this section, VLANs are configured per Table 2.
Create the in-band management VLAN and assign an IP address. Create the vMotion, vSAN, and VM
Network VLANs.
Configure VLANs – single switch
S5148F-ON
interface vlan1611
description InBand_Mgmt
ip address 172.16.11.254/24
no shutdown
interface vlan1612
description vMotion
no shutdown
interface vlan1613
description vSAN
no shutdown
interface vlan1614