Dell S5232F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 39

VLT validation commands

Get Dell S5232F-ON PDF manuals and user guides View all Dell S5232F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

8.1.5 show vrrp brief In this deployment, VRRP is configured on the in-band management VLAN, 1611, to provide gateway redundancy for management traffic. The output from the show vrrp brief command shows the master and virtual IP addresses and whether the switch is in the master or backup role. The switch configured with the largest priority value, shown in the Priority column, becomes the master. S5148F-Leaf1A#show vrrp brief Interface Group Priority Prempt State Version Master addr(s) Virtual addr vlan1611 IPv4 11 150 true master 2 172.16.11.253 172.16.11.254 Note: For the dual switch without VLT topology, the output is identical to that shown above. For the single switch topology, this command is not applicable. 8.2 VLT validation commands The following commands are only applicable to the dual switch with VLT topology. 8.2.1 show vlt domain_id This command is used to validate the VLT configuration status. The Role for one switch in the VLT pair is primary, and its peer switch (not shown) is assigned the secondary role. Ensure Peer-Routing is Enabled. The VLTi Link Status and VLT Peer Status must both be up. S5148F-Leaf1A#show vlt 127 Domain ID : 127 Unit ID : 1 Role : primary Version : 2.0 Local System MAC address : d8:9e:f3:c0:61:00 Role priority : 32768 VLT MAC address : d8:9e:f3:bf:ae:00 IP address : fda5:74c8:b79e:1::1 Delay-Restore timer : 90 seconds Peer-Routing : Enabled Peer-Routing-Timeout timer : 0 seconds VLTi Link Status port-channel1000 : up VLT Peer Unit ID System MAC Address Status IP Address Version 2 d8:9e:f3:bf:ae:00 up fda5:74c8:b79e:1::2 2.0 8.2.2 show vlt domain_id backup-link This command is used to verify VLT peers are communicating on the backup link over the OOB management network. The Destination is the management IP address of the peer. The Peer HeartBeat status must be Up. S5148F-Leaf1A#show vlt 127 backup-link 39 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON, S5232F-ON and S5148F-ON

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
39
Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON,
S5232F-ON and S5148F-ON
8.1.5
show vrrp brief
In this deployment, VRRP is configured on the in-band management VLAN, 1611, to provide gateway
redundancy for management traffic. The output from the
show vrrp brief
command shows the master
and virtual IP addresses and whether the switch is in the master or backup role. The switch configured with
the largest priority value, shown in the
Priority
column, becomes the master.
S5148F-Leaf1A#
show vrrp brief
Interface Group
Priority Prempt
State Version Master addr(s) Virtual addr
--------------------------------------------------------------------------------
vlan1611
IPv4 11
150
true
master
2
172.16.11.253
172.16.11.254
Note:
For the dual switch without VLT topology, the output is identical to that shown above. For the single
switch topology, this command is not applicable.
8.2
VLT validation commands
The following commands are only applicable to the dual switch with VLT topology.
8.2.1
show vlt
domain_id
This command is used to validate the VLT configuration status. The
Role
for one switch in the VLT pair is
primary
, and its peer switch (not shown) is assigned the
secondary
role. Ensure
Peer-Routing
is
Enabled
. The
VLTi Link Status
and
VLT Peer Status
must both be
up.
S5148F-Leaf1A#
show vlt 127
Domain ID
: 127
Unit ID
: 1
Role
: primary
Version
: 2.0
Local System MAC address
: d8:9e:f3:c0:61:00
Role priority
: 32768
VLT MAC address
: d8:9e:f3:bf:ae:00
IP address
: fda5:74c8:b79e:1::1
Delay-Restore timer
: 90 seconds
Peer-Routing
:
Enabled
Peer-Routing-Timeout timer : 0 seconds
VLTi Link Status
port-channel1000
:
up
VLT Peer Unit ID
System MAC Address
Status
IP Address
Version
--------------------------------------------------------------------------------
2
d8:9e:f3:bf:ae:00
up
fda5:74c8:b79e:1::2
2.0
8.2.2
show vlt
domain_id
backup-link
This command is used to verify VLT peers are communicating on the backup link over the OOB management
network. The
Destination
is the management IP address of the peer. The
Peer HeartBeat status
must be
Up.
S5148F-Leaf1A#
show vlt 127 backup-link