Dell S5248F-ON Open Networking Hardware Diagnostic Guide December 2021 - Page 40

PSU2_Out_amp | 4.500 ACPI_stat | 0x0 FAN1_prsnt | 0x0 FAN2_prsnt | 0x0 FAN3_prsnt | 0x0 FAN4_prsnt | 0x0 FAN1_Rear_stat | 0x0 FAN2_Rear_stat | 0x0 FAN3_Rear_stat | 0x0 FAN4_Rear_stat | 0x0 FAN1_Front_stat | 0x0 FAN2_Front_stat | 0x0 FAN3_Front_stat | 0x0 FAN4_Front_stat | 0x0 INTER_5.0V_volt | 4.900 INTER_3.3V_volt | 3.200 FPGA_1.0V_volt | 0.990 FPGA_1.2V_volt | 1.190 FPGA_1.8V_volt | 1.780 FPGA_3.3V_volt | 3.200 BMC_2.5V_volt | 2.400 BMC_1.15V_volt | 1.140 BMC_1.2V_volt | 1.200 SWITCH_6.8V_volt | 7.000 SWITCH_3.3V_volt | 3.300 SWITCH_1.8V_volt | 1.790 USB_5.0V_volt | 5.000 NPU_1.2V_volt | 1.190 NPU_VDDCORE_volt | 0.860 NPU_VDDANLG_volt | 0.790 BMC boot | 0x0 SEL_sensor | 0x0 root@dellemc-diag-os:~# | Amps | discrete | discrete | discrete | discrete | discrete | discrete | discrete | discrete | discrete | discrete | discrete | discrete | discrete | Volts | Volts | Volts | Volts | Volts | Volts | Volts | Volts | Volts | Volts | Volts | Volts | Volts | Volts | Volts | Volts | discrete | discrete | ok | na | na | 0x0180| na | na | 0x0180| na | na | 0x0180| na | na | 0x0180| na | na | 0x0180| na | na | 0x0080| na | na | 0x0080| na | na | 0x0080| na | na | 0x0080| na | na | 0x0080| na | na | 0x0080| na | na | 0x0080| na | na | 0x0080| na | na | ok | 4.200 | 4.500 | ok | 2.800 | 3.000 | ok | 0.850 | 0.900 | ok | 1.020 | 1.080 | ok | 1.530 | 1.620 | ok | 2.800 | 3.000 | ok | 2.100 | 2.200 | ok | 0.980 | 1.030 | ok | 1.020 | 1.080 | ok | 5.800 | 6.100 | ok | 2.800 | 3.000 | ok | 1.530 | 1.620 | ok | 4.200 | 4.500 | ok | 1.020 | 1.080 | ok | 0.700 | 0.720 | ok | 0.680 | 0.720 | 0x0180| na | na | 0x2080| na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | 4.700 | 5.200 | 3.100 | 3.500 | 0.950 | 1.050 | 1.140 | 1.260 | 1.710 | 1.890 | 3.100 | 3.500 | 2.300 | 2.600 | 1.090 | 1.210 | 1.140 | 1.260 | 6.400 | 7.200 | 3.100 | 3.500 | 1.710 | 1.890 | 4.700 | 5.200 | 1.140 | 1.260 | 0.740 | 0.910 | 0.760 | 0.840 | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | 5.500 | 3.600 | 1.100 | 1.320 | 1.980 | 3.600 | 2.800 | 1.270 | 1.320 | 7.500 | 3.600 | 1.980 | 5.500 | 1.320 | 0.930 | 0.880 | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | na | 5.700 | 3.800 | 1.150 | 1.380 | 2.070 | 3.800 | 2.900 | 1.320 | 1.380 | 7.800 | 3.800 | 2.070 | 5.700 | 1.380 | 0.950 | 0.920 | na | na ledtool The ledtool allows you to control the state of the front and back panel light emitting diodes (LEDs). ASIC and Phys control the port LEDs and are beyond the scope of this tool. You can manually control the front and back panel LEDs normally controlled through the CPLD or FPGA access. When set, bits in these registers control the state of the LED. Tests To test the LEDs, use the ledtool --test command. root@dell-diag-os:/opt/dellemc/diag/bin# ./ledtool --test LED Test Started... Will take few mins to complete. LED Tool: Overall test results Passed CLI options DellEmc Diag - Led Tool version 1.0, x.xx.x.x-x build, 2017/05/23, Usage: List the LEDs:= ledtool --list (or) ledtool -l Get the state of (specific) LED(s):= ledtool --get [--led=] (or) ledtool -g [-D ] Set the state of specific LED(color and blink):= ledtool --set --led= [--instance=] {--state= | --val=} (or) ledtool -s -D [-I ] {-T | -V } Execute repeatedly command by count:= ledtool --iteration=max/ [option1] [option2]... 40 Dell EMC DAIG-OS tools