Denon AVR 3300 Owners Manual - Page 39

Example: Stereo, Input mode display, Input signal display - optical input

Get Denon AVR 3300 - Dolby Digital Audio/Video Receiver PDF manuals and user guides
UPC - 081757503846
View all Denon AVR 3300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

ENGLISH • Selecting the PCM mode Press the PCM button to switch to the PCM signal input. PCM (Main unit) • Selecting the DTS mode Press the DTS button to switch to the DTS signal input. DTS (Main unit) 3 Select the play mode. Example: Stereo SELECT STEREO (Main unit) (Remote control unit) * To select the surround mode while adjusting the surround parameters, channel volume or tone control, press the surround mode button then operate the selector. (Main unit) 4 Start playback on the selected component. • For operating instructions, refer to the component's manual. 5 Adjust the volume. MASTER VOLUME MASTER VOL. Input mode display • In the AUTO mode INPUT AUTO PCM DTS • In the DIGITAL PCM mode INPUT AUTO PCM DTS • In the DIGITAL DTS mode INPUT AUTO PCM DTS • In the ANALOG mode INPUT AUTO PCM DTS One of these lights, depending on the input signal. ANALOG DIGITAL DIGITAL DIGITAL ANALOG Input signal display • DOLBY DIGITAL SIGNAL LOCK DIGITAL • DTS LOCK SIGNAL DIGITAL • PCM LOCK SIGNAL DIGITAL * The LOCK LED lights when digital signals are being input properly. If the LED does not light, check whether the digital input component setup (page 25) and connections are correct and whether the component's power is turned on. NOTE: • The digital input indicator will light when playing CD-ROMs containing data other than audio signals, but no sound will be heard. The volume level is displayed on the master volume level display. (Main unit) (Remote control unit) * The volume can be adjusted within the range of -60 to 0 to 18 dB, in steps of 1 dB. However, when the channel level is set as described on page 23 or pages 44 and 45, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is "18 dB - (Maximum value of channel level)".) Input mode when playing DTS sources • Noise will be output if DTS-compatible CDs or LDs are played in the "ANALOG" or "PCM" mode. When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to "DTS". 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
LOCK
SIGNAL
DIGITAL
LOCK
SIGNAL
DIGITAL
LOCK
SIGNAL
DIGITAL
ANALOG
DIGITAL
DIGITAL
DIGITAL
ANALOG
AUTO
INPUT
PCM
DTS
AUTO
INPUT
PCM
DTS
AUTO
INPUT
PCM
DTS
AUTO
INPUT
PCM
DTS
39
ENGLISH
PCM
•
Selecting the PCM mode
Press the PCM button to switch to the PCM signal input.
DTS
•
Selecting the DTS mode
Press the DTS button to switch to the DTS signal input.
3
Example: Stereo
Select the play mode.
STEREO
(Main unit)
(Remote control unit)
4
Start playback on the selected component.
• For operating instructions, refer to the component’s
manual.
5
Adjust the volume.
MASTER VOLUME
MASTER VOL.
The volume level is
displayed on the
master volume level
display.
(Main unit)
(Remote control unit)
*
The volume can be adjusted within the range of –60 to 0 to 18 dB,
in steps of 1 dB. However, when the channel level is set as
described on page 23 or pages 44 and 45, if the volume for any
channel is set at +1 dB or greater, the volume cannot be adjusted
up to 18 dB. (In this case the maximum volume adjustment range
is “18 dB — (Maximum value of channel level)”.)
Input mode when playing DTS sources
•
Noise will be output if DTS-compatible CDs or LDs are played in the
“ANALOG” or “PCM” mode.
When playing DTS-compatible sources, be sure to connect the
source component to the digital input jacks (OPTICAL/COAXIAL)
and set the input mode to “DTS”.
Input mode display
•
In the AUTO mode
•
In the DIGITAL PCM mode
•
In the DIGITAL DTS mode
•
In the ANALOG mode
One of these lights, depending on the
input signal.
Input signal display
•
DOLBY DIGITAL
• DTS
• PCM
*
The LOCK LED lights when digital signals are being input properly.
If the LED does not light, check whether the digital input
component setup (page 25) and connections are correct and
whether the component’s power is turned on.
NOTE:
• The digital input indicator will light when playing CD-ROMs
containing data other than audio signals, but no sound will be
heard.
(Main unit)
(Main unit)
SELECT
*
To select the surround mode while adjusting the surround
parameters, channel volume or tone control, press the
surround mode button then operate the selector.
(Main unit)