Denon AVR-890 Owners Manual - English - Page 34

Getting Started Connections Settings Playback Multi-Zone Remote Control Information Troubleshooting Specifications ENGLISH Setting items Setting contents 2CH DIRECT/STEREO Setting : Select the method for setting the speakers used in the 2-channel Make speaker settings for 2- direct and stereo playback modes. channel mode playback. • Basic : The settings at "Speaker Setup" (vpage 27) are applied. • Custom : Make separate settings for 2-channel mode. Front : Set the front speaker size. • Large : Use of a large speaker that can adequately play back low frequencies. • Small : Use of a small speaker that has inadequate playback capacity for low frequencies. SW : Set the presence of a subwoofer. • Yes : Use a subwoofer. • No : Select when a subwoofer is not connected. SW Mode : Select low range signal to be reproduced by subwoofer. • LFE : Add the low frequency signal of the channel for which the speaker size is set to "Small" to the subwoofer signal and output it. • LFE+Main : Add the low frequency signal of all channels to the subwoofer signal and output it. Crossover : Outputs at below set frequency, each speaker's bass signal output from the subwoofer. • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz Distance FL / Distance FR : Select the speaker you want to set, and set the CH Level. Set the value that is closest to the measured distance. • 0.0ft ~ 60.0ft (12.0ft) / 0.00m ~ 18.00m (3.6m) CH Level FL/ CH Level FL FR : Select the speaker you want to set, and set the CH Level. Adjust the level of each channel. • -12.0dB ~ +12.0dB(0.0dB) Auto Surround Mode ON : Memorize settings. Most recently stored surround mode is Make setting for memorizing automatically selected. surround mode setting for OFF : Do not memorize settings. Surround mode does not change each input signal type. according to input signal. The auto surround mode function lets you store in the memory the surround mode last used for playing the four types of input signals listed below. q Analog and PCM 2-channel signals w Dolby Digital and DTS 2-channel signals e Dolby Digital and DTS multi-channel signals r Multi-channel signals other than Dolby Digital and DTS (PCM, etc.) NOTE When playing in the PURE DIRECT mode, the surround mode does not change even if the input signal is changed. Making detailed settings (Manual Setup) Setting items Setting contents EQ Customize Audyssey Byp. L/R / Audyssey Flat / Manual Set so that unused equalizer • Used settings are not displayed • Not Used when is used. NOTE • Set so that "Audyssey Byp. L/R" and "Audyssey Flat" settings can be made when Audyssey™ Auto Setup is performed. • Equalizer settings for which "Not Used" is set with the Quick Select function cannot be stored and called out. Making the ZONE2 settings (ZONE2 Setup) Default settings are underlined. Make settings for audio playback in a ZONE2 system. "ZONE2 Setup" is displayed when ZONE2 is selected with "Amp Assign" (vpage 27). Setting items Setting contents Level Lch -12dB ~ +12dB (0dB) Adjust the left channel output level. Level Rch -12dB ~ +12dB (0dB) Adjust the right channel output level. Volume Display Set the ZONE2 display method. Relative : The volume is displayed within the range of - - -dB (Minimum), volume -80 dB ~ +18 dB. Absolute : The volume is displayed within the range of 0, 1 ~ 99. Vol.Limit OFF : Do not set a maximum volume. Make a setting for maximum -20dB(61) / -10dB(71) / 0dB(81) volume. Power On Level Last : Use the memorized setting from the last session. Define the volume setting - - - : Always use the muting on condition when power is turned on. that is active when the power -80dB(1) ~ +18dB(99) : The volume is adjusted to the set level. is turned on. Mute Level Full : The sound is cut off entirely. Set the amount of attenuation -40dB : The sound is attenuated by 40 dB. when muting is on. -20dB : The sound is attenuated by 20 dB. • The volume is displayed using the display method set at "Volume Display" (vpage 31). • Set the main volume at "Volume Control" (vpage 32).  Remote control operation buttons Displaying the menu : Cancel the menu : Moves the cursor (Up/Down/Left/Right) : Decision the setting : Return to previous menu