Denon AVR2310CI Owners Manual - Page 27
Connect the included Setup Microphone, Audyssey Auto Setup Preparations - avr 2310ci setup
UPC - 837654710111
View all Denon AVR2310CI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 27 highlights
ENGLISH Getting Started Connections Settings Playback Multi-Zone Remote Control Information Troubleshooting Specifications Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup) a Connect the included Setup Microphone NOTE • Do not disconnect the setup microphone until the Audyssey Auto Setup procedure is completed. • When using headphones, unplug the headphones before starting the Audyssey Auto Setup procedure. 1 Check the speaker connections. (vpage 12 "Connecting the Speakers") 2 Turn on the power of the TV and subwoofer. Set the TV's input to the AVR-2310CI. 3 Turn on the AVR-2310CI's power. (vpage 20 "Turning the Power On") 4 Connect the included calibrated setup microphone to the SETUP MIC jack on the main unit. The Audyssey Auto Setup screen appears automatically. NOTE • Do not hold the microphone in your hand during measurements. • Avoid placing the microphone close to a seat back or wall as sound reflections may give inaccurate results. When using a subwoofer on which the volume can be adjusted and the crossover frequency can be set When using a subwoofer, make the following settings before starting the Audyssey Auto Setup procedure: n When using a subwoofer with a direct mode Set the direct mode to "On" and disable the volume adjustment and crossover frequency setting. n When using a subwoofer without a direct mode Make the following settings: • Volume : "12 o'clock position" • Crossover frequency : "Maximum/Highest Frequency" • Low pass filter : "Off" • Standby mode : "Off" Sound receptor 5 Mount the setup microphone on a tripod or stand and install it at the main listening position. When installing the setup microphone, adjust its height so that the section where the sound is received is at the height of the ears during listening. Setup microphone s Audyssey Auto Setup Preparations around items indicate the settings made upon purchase. STEP1 Preparation Perform the following settings if adjustments, etc., are required for the speaker environment you're using. If you do not need to perform the following settings, or have already completed them, select "Auto Setup Start" and then press . Proceed to " STEP2 ". Changing the amplifier assignment (Amp Assign) The signals output from the AVR-2310CI's SURR. BACK/AMP ASSIGN speaker terminals can be switched to signals of the surround mode being used. 1 Press ui to select "Amp Assign", then press . AUTO SETUP AUDYSSEY AUTO SETUP MultEQ STEP1 Preparation Connect the speakers and place them according to the recommendaations in the manual. Set the following items if nesessary. Amp Assign Channel Select Auto Setup Start [1/6] ENTER Enter RETURN Cancel Set use of surround back ch. for your system 2 Press o p to select Amp Assign Mode, then press . Normal : The sound of the surround back channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. ZONE2 : If the ZONE2 power is on, the sound of the ZONE2 channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. Front A Bi-Amp : The sound of the front A bi-amp channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. Front B Bi-Amp : The sound of the front B bi-amp channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. Front Height : The sound of the front height channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. Remote control operation buttons Displaying the menu : Cancel the menu : Moves the cursor (Up/Down/Left/Right) n To cancel Audyssey Auto Setup To cancel, press then use o p to select "Yes". : Decision the setting : Return to previous menu 24