Denon DN X1700 Owners Manual - Page 8
Source Sel Ln1/ln2/ln3/ln4/d1-4/usb - digital
UPC - 883795000864
View all Denon DN X1700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
Getting Started Connections Basic Operations Effector Function Fader Start USB Utility Specifications Troubleshooting Q5 Effect ON/OFF button This sets the effects of EFX 1 or EFX 2 to ON or OFF. Q6 CROSSFADER Controls the relative output level from the summed A and B Mixes. When the fader is at its far left, only the A Mix is heard from the Outputs. As the fader is moved toward the right, the amount of B Mix is increased and the amount of A Mix is decreased. When the fader is centered, equal amounts of A and B Mixes are routed to the Outputs. Fully right is all B Mix at the Outputs. Q7 Channel input fader (CH FADER) Controls the level of the selected Input. Q8 HEADPHONE output jack Accepts 1/4" stereo headphone plugs. Q9 HEADPHONE level control Adjusts the volume for the headphones. W0 HEADPHONE PAN control This is used to adjust the balance between the CUE sound and the master sound which are monitored using the headphones. W1 SPLIT CUE button There are two headphone monitor modes. Stereo mode (SPLIT CUE OFF): The cue signals and master signals can be monitored in stereo. SPLIT CUE mode: The monaural cue signals are heard through the left channel of the headphones, and the monaural master signals through the right channel. W2 CROSSFADER CONTOUR control Allows adjusting the "shape" of the Crossfader response from a gentle curve for smooth, long running fades, to the steep pitch required for top performance cut and scratch effects. W3 CH FADER CONTOUR control Adjusts the volume curve response of the channel fader. W4 CH FADER START switch This function will start the performance of CD/ Media Player with Ch. Fader automatically is ON/OFF. W5 CROSSFADER START switches Use this to switch the Crossfader Start function ON and OFF. W6 MIC SEND LEVEL control This is used to adjust the level at which the mic signals are sent to the master output. W7 Mic EFX INS 1, 2 buttons These buttons enable the various effects of the selected side, either EFX 1 or EFX 2, to be obtained for the mic input signals. W8 MIC EQ controls Contour the frequency response of the Mic input -15 dB to +15 dB. W9 DUCKING ON/OFF button • Use this to switch the Talk Over function ON and OFF. (ON/OFF is cyclic) • When the button is lit, level of signals except Mics is attenuated. * The ducking attenuation level can be adjusted in the "UTILITY" mode. E0 MIC1, MIC2 TRIM controls Adjusts the level of the Main Mic input. E1 MIC1, 2 buttons When the button's LED is lighted, the mic signals take effect. E2 CD/PHONO line input selector buttons These enable the line input of each channel to be selected as CD or PHONO. CD: Rear panel LINE1-4 CD terminal input PHONO: Rear panel LINE1-4 PHONO terminal input E3 SOURCE SEL LN1/LN2/LN3/LN4/D1-4/USB controls (channel input selector) These enable any of six inputs to be selected for each of the channels. The same input can be selected for more than one channel. When DIGITAL is selected, the LED of the corresponding button lights up red; when USB is selected, it lights up blue. LINE1 LINE2 LINE3 LINE4 DIGITAL USB SOURCE SEL SOURCE SEL CH1 CH4 4 E4 MIDI layer selector buttons When these buttons are set to ON, the controls of the selected channels function as MIDI controllers. Also, the EQ control rings light up blue. E5 Channel input LEVEL controls These are used to adjust the levels of the selected inputs. E6 Channel isolator EQ controls (HI, MID, LOW) These are used to change the frequency response of the selected inputs. At the center position, the frequency response is flat. At the -∞ position, the frequencies of all the bands are cut off completely. E7 CH LEVEL meter Displays the input level after adjusted with LEVEL E5 and Source EQ E6 controls. E8 Channel EFX SEND 1, 2 buttons These buttons enable the various effects of the selected side, either EFX 1 or EFX 2, to be obtained for the channel audio signals. The same effect (EFX 1 or 2) can be selected for a multiple number of channels. The LED of the EFX button for the side selected for each channel lights. E9 Channel CUE buttons Pressing in any or all of CUE buttons routes the respective source to the headphone and meter cue sections. Pressing multiple buttons makes it possible to derive mixed sound from the selected sources. *The SOLO mode with no signals mixed can also be selected as a preset. R0 CROSSFADER ASSIGN switches A, B: The channel source is assigned to A or B of the Crossfader. THRU: Select when you don't assign the channel source into the Crossfader. R1 MASTER BALANCE control Adjusts the L/R balance of the MASTER output. R2 L/CUE, R/PGM master level meter One of two modes can be selected for display on this meter. Split CUE OFF: The master output audio level is displayed. Split CUE ON: The right channel master CUE (monaural) and left channel CUE (monaural) audio levels are displayed. R3 SIG/PK This is the signal/peak meter for the mic input level. Off: No signals input (under -60 dB/FS) Green: Signal input (-60 dB/FS to under -20 dB/FS) Orange: Suitable signal input level (-20 dB/FS to under -6 dB/FS) Red: Excessively high signal input level (above -6 dB/ FS)