Dewalt D28065N Instruction Manual - Page 13

Accessories, Mounting Guard, 3 mm and 5 127 mm, Sanding Flap Discs

Get Dewalt D28065N PDF manuals and user guides View all Dewalt D28065N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

English (114.3 mm) and 5" (127 mm) Sanding Flap Discs Type 27 guard Type 27 guard hubbed sanding flap disc Quick-Change backing flange non-hubbed sanding flap disc threaded clamp nut NOTE: If the gear case and motor housing become separated by more than 1/4" (6.35 mm), the tool must be serviced and re-assembled by a DEWALT service center. Failure to have the tool serviced may cause brush, motor and bearing failure. 4. Re-install screws to attach the gear case to the motor housing. Tighten screws to 18 in./lbs. (2.03 Nm) torque. Overtightening could cause screws to strip. 5. Re-install guard and correct flanges for the appropriate accessories. Accessories It is important to choose the correct guards, backing pads and flanges to use with grinder accessories. See pages 9-11 for information on choosing the correct accessories. WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated accessory speed may burst and cause injury. Threaded accessories must have a 5/8"-11 hub. Every unthreaded accessory must have a 7/8" (22.2 mm) arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 9-11 of this manual. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate. Mounting Guard MOUNTING AND REMOVING GUARD (FIG. 3, 4) CAUTION: Guards must be used with all grinding wheels, sanding flap discs, wire brushes, and wire wheels. The tool may be used without a guard only when sanding with conventional sanding discs. Some DEWALT models are provided with a guard intended for use with depressed center wheels (Type 27) and hubbed grinding wheels (Type 27). The same guard is designed for use with sanding flap discs (Type 27 and 29) and wire brushes. Grinding and cutting with wheels other than Type 27 and 29 require different accessory guards not included with tool. Mounting instructions for these accessory guards are included in the accessory package. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
English
11
5. Re-install guard and correct flanges for the appropriate
accessories.
Accessories
It is important to choose the correct guards, backing pads and flanges
to use with grinder accessories. See pages 9–11 for information on
choosing the correct accessories.
WARNING:
Accessories must be rated for at least the speed
recommended on the tool warning label. Wheels and other accessories
running over rated accessory speed may burst and cause injury.
Threaded accessories must have a 5/8"-11 hub. Every unthreaded
accessory must have a 7/8" (22.2 mm) arbor hole. If it does not, it
may have been designed for a circular saw and should not be used.
Use only the accessories shown on pages 9–11 of this manual.
Accessory ratings must be above listed minimum wheel speed as
shown on tool nameplate.
Mounting Guard
MOUNTING AND REMOVING GUARD (FIG. 3, 4)
CAUTION:
Guards must be used with all grinding wheels, sanding
flap discs, wire brushes, and wire wheels. The tool may be used
without a guard only when sanding with conventional sanding discs.
Some D
E
WALT models are provided with a guard intended for use
with depressed center wheels (Type 27) and hubbed grinding wheels
(Type 27). The same guard is designed for use with sanding flap discs
(Type 27 and 29) and wire brushes. Grinding and cutting with wheels
other than Type 27 and 29 require different accessory guards not
included with tool. Mounting instructions for these accessory guards
are included in the accessory package.
(114.3 mm) and 5" (127 mm)
Sanding Flap Discs
hubbed sanding
flap disc
Quick-Change
backing flange
non-hubbed sanding
flap disc
threaded clamp nut
Type 27 guard
Type 27 guard
NOTE:
If the gear case and motor housing become separated
by more than 1/4" (6.35 mm), the tool must be serviced and
re-assembled by a D
E
WALT service center. Failure to have the tool
serviced may cause brush, motor and bearing failure.
4. Re-install screws to attach the gear case to the motor housing.
Tighten screws to 18 in./lbs. (2.03 Nm) torque. Overtightening
could cause screws to strip.