Dewalt D55154 Instruction Manual - Page 11

INSTALLATION, Assembly Fig. 1 - reset

Get Dewalt D55154 PDF manuals and user guides View all Dewalt D55154 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

English Drain Valve The drain valve (H) is located at the base of the air tank and is used to drain conden- sation at the end of each use. See Draining Air Tank under Maintenance. H Cooling System This compressor contains an advanced design cooling system. It is normal for this fan to blow air through the vent holes in large amounts. The cooling system is working when air is expelled. Air Compressor Pump The pump compresses air into the air tank. Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet. Motor Overload Protector This motor has a manual thermal overload protector. If the motor overheats for any reason, the overload protector will shut off the motor. The motor must be allowed to cool down before restarting. To restart: 1. Ensure the On/Off switch (A) is in the OFF position. K 2. Allow the motor to cool. 3. Depress the reset button (M) on the motor. Oil dipstick The oil dipstick (K) indicates the amount M of oil in the pump. Check pump oil daily, see Compressor Pump Oil under Maintenance. AIR INTAKE FILTER The filter (N) is designed to clean air entering the pump. To ensure the pump continually receives a clean, cool, and dry air supply the filter must always be clean and the filter intake must be free from obstructions. INSTALLATION Assembly (Fig. 1) INSTALLING HANDLE Caution: Risk of personal injury. Avoid placing hands between handle and top panel when assembling to prevent pinching. 1. Place handle (O) into bushings on top panel (Q). 2. Depress snap buttons and slide handle through first bushings until it stops at second bushings. 3. Reach under top panel and depress snap buttons again and slide through second bushings. 4. Pull handle all the way up until it stops. Turn knobs (P) to lock handle in place. IMPORTANT: Always pull handle up and lock in place before using as a dolly. 5. If not using the dolly feature, loosen knobs and push handle down until it stops. Installing Hoses Warning: Risk of unsafe operation. Firmly grasp hose in hand when installing or disconnecting to prevent hose whip. 1. Ensure regulated pressure gauge reads 0 PSI (0 kPa). 2. Grasp the hose at the quick connect plug and push the plug into the quick connect body (E). Coupler will snap into place. 3. Grasp the hose and pull to ensure coupler is seated. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
11
English
DRAIN VALVE
The drain valve (H) is located at the base
H
of the air tank and is used to drain conden-
sation at the end of each use.
See
Draining
Air Tank
under
Maintenance.
COOLING SYSTEM
This compressor contains an advanced design cooling system.
It is normal for this fan to blow air through the vent holes in large
amounts. The cooling system is working when air is expelled.
AIR COMPRESSOR PUMP
The pump compresses air into the air tank. Working air is not
available until the compressor has raised the air tank pressure
above that required at the air outlet.
MOTOR OVERLOAD PROTECTOR
This motor has a manual thermal overload protector. If the motor
overheats for any reason, the overload protector will shut off the
motor. The motor must be allowed to cool down before restarting.
To restart:
1. Ensure the On/Off switch (A) is in the
M
K
OFF position.
2. Allow the motor to cool.
3. Depress the reset button (M) on the
motor.
OIL DIPSTICK
The oil dipstick (K) indicates the amount
of oil in the pump. Check pump oil daily,
see
Compressor
Pump
Oil
under
Maintenance
.
AIR INTAKE FILTER
The filter (N) is designed to clean air entering the pump. To ensure
the pump continually receives a clean, cool, and dry air supply the
filter must always be clean and the filter intake must be free from
obstructions.
INSTALLATION
Assembly (Fig. 1)
INSTALLING HANDLE
CAUTION:
Risk of personal injury. Avoid placing hands between
handle and top panel when assembling to prevent pinching.
1. Place handle (O) into bushings on top panel (Q).
±. Depress snap buttons and slide handle through first bushings
until it stops at second bushings.
². Reach under top panel and depress snap buttons again and
slide through second bushings.
4. Pull handle all the way up until it stops. Turn knobs (P) to lock
handle in place.
IMPORTANT:
Always pull handle up and lock in
place before using as a dolly.
5. If not using the dolly feature, loosen knobs and push handle
down until it stops.
INSTALLING HOSES
WARNING:
Risk of unsafe operation. Firmly grasp hose in hand
when installing or disconnecting to prevent hose whip.
1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).
±. Grasp the hose at the quick connect plug and push the plug
into the quick connect body (E). Coupler will snap into place.
². Grasp the hose and pull to ensure coupler is seated.