Dewalt DCMWSP255Y2 Instruction Manual - Page 14
Charging a Battery Fig. C
View all Dewalt DCMWSP255Y2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
English • Always unplug the charger from the power supply when there is no battery pack in the cavity. Charging a Battery (Fig. C) 1. Plug the charger into an appropriate outlet. 2. Insert and fully seat battery pack. The red charging light will continuously blink while charging. 3. Charging is complete when the red charging light remains continuously ON. Battery pack can be left in charger or removed. Some chargers require the battery pack release button to be pressed for removal. 4. Charger will not charge a faulty battery pack, which may be indicated by the light staying OFF. Take charger and battery pack to an authorized service center if light stays OFF. NOTE: Refer to label near charging light on charger for blink patterns. Older chargers may have additional information and/or may not have a yellow indicator light. Hot/Cold Pack Delay When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate temperature. The charger then automatically switches to the pack charging mode. This feature ensures maximum battery pack life. A cold battery pack may charge at a slower rate than a warm battery pack. The hot/cold pack delay will be indicated by the red light continuing to blink but with the yellow light continuously ON. Once the battery pack has reached an appropriate temperature, the yellow light will turn OFF and the charger will resume the charging procedure. DCB118 and DCB1112 Chargers The DCB118 and DCB1112 chargers are equipped with an internal fan designed to cool the battery pack. The fan will turn on automatically when the battery pack needs to be cooled. Electronic Protection System Li‑Ion tools are designed with an Electronic Protection System that will protect the battery pack against overloading, overheating or deep discharge. The tool will automatically turn off and the battery pack will need to be recharged. Important Charging Notes 1. Longest life and best performance can be obtained if the battery packs are 24 charged when the air temperature is between 65 °F - 75 °F (18 ° C- 24 °C). DO NOT charge when the battery pack is below +40 °F (+4.5 °C), or above +104 °F (+40 °C). This is important and will prevent serious damage to the battery pack. 2. The charger and battery pack may become warm to the touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed or an uninsulated trailer. 3. If the battery pack does not charge properly: a. Check operation of receptacle by plugging in a lamp or other appliance; b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights; c. If charging problems persist, take the tool, battery pack and charger to your local service center. 4. You may charge a partially used pack whenever you desire with no adverse effect on the battery pack. Charger Cleaning Instructions WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non‑metallic brush. Do not use water or any cleaning solutions. Wall Mounting Some DeWALT chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or other obstructions which may impede air flow. Use the back of the charger as a template for the location of the mounting screws on the wall. Mount the charger securely using drywall screws (purchased separately) at least 1" (25.4 mm) long, with a screw head diameter of 0.28-0.35" (7-9 mm), screwed into wood to an optimal depth leaving approximately 7/32" (5.5 mm) of the screw exposed. Align the slots on the back of the charger with the exposed screws and fully engage them in the slots. SAVE THESE INSTRUCTIONS FOR FUTURE USE ASSEMBLY AND ADJUSTMENTS DANGER: To reduce the risk of serious personal injury, turn unit off and remove the safety key and battery packs before making any adjustments or removing/installing attachments or accessories. An accidental start‑up can cause injury. Adjusting Handle Height (Fig. D) The mower is shipped in storage mode. You will need to adjust the handle to operating position before continuing. 1. To unlock the lower handle 17 from the storage position, twist the two handle lock knobs 7 a quarter turn. The handle lock knobs are located on both sides of the lower handle. 2. Raise the lower handle to the most comfortable operating position, choosing the lower or upper hole on each side bracket. Take care to not pinch or stress the cord. 3. Twist the handle lock knobs a quarter turn, securing the lower handle into position. Attaching Upper Handle (Fig. E) 1. Line up the holes on the bottom of the upper handle 4 with the holes on the top of the lower handle 17 . Take care to not pinch or stress the cord. 12