Dewalt DCS369B Instruction Manual - Page 10
Belt Hook Fig. C, Blade Installation and Removal Fig. B, ASSEMBLY AND ADJUSTMENTS, Intended Use,
View all Dewalt DCS369B manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
English Charger Cleaning Instructions WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. Wall Mounting DCB107, DCB112, DCB113, DCB115, DCB118, DCB132 These chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or other obstructions which may impede air flow. Use the back of the charger as a template for the location of the mounting screws on the wall. Mount the charger securely using drywall screws (purchased separately) at least 1" (25.4 mm) long, with a screw head diameter of 0.28-0.35" (7-9 mm), screwed into wood to an optimal depth leaving approximately 7/32" (5.5 mm) of the screw exposed. Align the slots on the back of the charger with the exposed screws and fully engage them in the slots. Intended Use This reciprocating saw is designed for professional sawing applications. DO NOT use under wet conditions or in presence of flammable liquids or gases. This reciprocating saw is a professional power tool. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. ASSEMBLY AND ADJUSTMENTS WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. WARNING: Cut hazard. Turn off and remove battery from tool before making any adjustments or removing or installing attachments or accessories. WARNING: Cut hazard. Blade breakage may occur if the blade does not extend past the adjustable shoe and the workpiece throughout the cut. Increased risk of personal injury, as well as damage to the adjustable shoe and workpiece may result. Blade Installation and Removal (Fig. B) Different blade lengths are available. Use the appropriate blade for the application. The blade should be longer than 3-1/2" (89 mm) and should extend past the shoe and the thickness of the workpiece throughout the cut. Do not use jigsaw blades with this tool. To Install Blade into Saw 1. Twist open the blade clamp 3 to its full open position. 2. Insert blade 11 fully into blade clamp. 3. Release blade clamp. Gently tug on the blade to ensure blade is clamped securely. NOTE: Blade can be installed upside-down to assist in flush‑to cutting. Fig. B 3 11 To Remove Blade from Saw (Fig. B) WARNING: Burn hazard. Do not touch the the blade immediately after use. Contact with the blade may result in personal injury. 1. Twist open blade clamp 3 to its full open position. 2. Remove blade 11 . Belt Hook (Fig. C) WARNING: To reduce the risk of serious personal injury, ONLY use the tool's belt hook to hang the tool from a work belt. DO NOT use the belt hook for tethering or securing the tool to a person or object during use. DO NOT suspend tool overhead or suspend objects from the belt hook. WARNING: To reduce the risk of serious personal injury, ensure the screw holding the belt hook is secure. WARNING: Before hanging the tool from a work belt, ALWAYS remove the blade and ensure that the lock-off button is in the locked postion to eliminate unintentional starting. IMPORTANT: When attaching or replacing the belt hook 12 , use only the screw 13 that is provided. Be sure to securely tighten the screw. The belt hook 12 can be attached to either side of the tool using only the screw 13 provided, to accommodate left- or right- handed users. If the belt hook is not desired at all, it can be removed from the tool. To move the belt hook, remove the screw that holds it in place then reassemble on the opposite side. Be sure to securely tighten the screw. 8