EVGA 132-CK-NF79-TR User Manual - Page 27

Connecting IDE Hard Disk Drives

Get EVGA 132-CK-NF79-TR PDF manuals and user guides View all EVGA 132-CK-NF79-TR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

nForce 790i Ultra SLI Motherboard Connector Pin Signal 9 +5V_AUX 10 +12V 11 +12V 12 +3.3V Pin Signal 21 +5V 22 +5V 23 +5V 24 GND 8-pin ATX 12V Power (PWR2) PWR2, the 8-pin ATX 12V power connection, is used to provide power to the CPU. Align the pins to the connector and press firmly until seated. Backpanel connector edge GND 1 4 5 8 12V Connecting IDE Hard Disk Drives The IDE connector supports Ultra ATA 133/100/66 IDE hard disk drives. 1. Connect the blue connector (the cable end with a single connector) to the motherboard. 2. Connect the black connector (the cable with the two closely spaced black and gray connectors) to the Ultra ATA master device. 3. Connect the gray connector to a slave device. If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. EVGA Corporation 16 January 11, 2008 | DU-03751-001_v01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
nForce 790i Ultra SLI Motherboard
EVGA Corporation
16
January 11, 2008
|
DU-03751-001_v01
Connector
Pin
Signal
Pin
Signal
9
+5V_AUX
21
+5V
10
+12V
22
+5V
11
+12V
23
+5V
12
+3.3V
24
GND
8-pin ATX 12V Power (
PWR2
)
PWR2
, the 8-pin ATX 12V power connection, is used to provide power to
the CPU. Align the pins to the connector and press firmly until seated.
Connecting IDE Hard Disk Drives
The IDE connector supports Ultra ATA 133/100/66 IDE hard disk drives.
1.
Connect the blue connector (the cable end with a single connector) to
the motherboard.
2.
Connect the black connector (the cable with the two closely spaced
black and gray connectors) to the Ultra ATA master device.
3.
Connect the gray connector to a slave device.
If you install two hard disk drives, you must configure the second drive as
a slave device by setting its jumper accordingly. Refer to the hard disk
documentation for the jumper settings.
GND
12V
4
5
8
1
Backpanel connector edge