Electrolux E15IM60GPS Complete Owner's Guide (English) - Page 18

Important

Get Electrolux E15IM60GPS PDF manuals and user guides View all Electrolux E15IM60GPS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

18 Maintenance 2 Remove all ice from the storage bin. 3. Remove inside front cover. (See figure 31.) FRONT COVER Figure 31 4. Remove Remove the overflow tube by lifting it while using a slight back and forth motion to loosen it from the drain hole. The water in the reservoir will flow down the drain. (See figure 32.) OVERFLOW 8 Reinstall inside front cover. 9 When the self-cleaning process stops (approximately 45 minutes) the unit will remain off for an additional 15 minutes. When the clean cycle is completed, the display will automatically switch back to set temperature and unit will run as normal operation. 10 Clean the storage bin. (See INTERIOR CLEANING). Sanatize the bin with a solution of 1 tablespoon of bleach and 1 gallon of warm water. Rinse thoroughly with clean water. 11 To ensure the drain system is working properly, pour 1 gallon of cool, fresh water into the ice bin. The water should drain freely. If the unit is equipped with a drain pump, it should drain the ice bin. When ice production resumes, the water fill valve will energize, fill the water reservoir, and shutoff after three minutes. The compressor begins to operate and water flows over the evaporator assembly (ice cube tray). Initially, the water flow may not be uniform, causing uneven sized cubes or water to spill into the ice storage bin. This is a normal situation that will correct itself within the first 24 hours of operation. IMPORTANT • Discard all ice produced in the first harvest. • If power gets interrupted during the selfclean cycle, it will be necessary to repeat the complete cleaning cycle after power is restored. Figure 32 UL209a 5 Replace the overflow tube after all of the water has drained from the reservoir. 6 Start the cleaning cycle as follows: a Touch and hold the POWER button. b Touch and release the LIGHT button three times, then release the POWER button. c The display will show "CL" to confirm the beginning of the cleaning cycle. 7 When water begins to flow over the evaporator (approximately 3 minutes), add one package of Electrolux Ice Machine Cleaner to the water reservoir.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
18
5
Replace the overflow tube after all of the
water has drained from the reservoir.
6
Start the cleaning cycle as follows:
a
Touch and hold the POWER button.
b
Touch and release the LIGHT button
three times, then release the POWER
button.
c
The display will show “CL” to confirm the
beginning of the cleaning cycle.
7
When water begins to flow over the
evaporator (approximately 3 minutes), add
one package of Electrolux Ice Machine
Cleaner to the water reservoir.
OVERFLOW
Figure 32
FRONT
COVER
Figure 31
2
Remove all ice from the storage bin.
3.
Remove inside front cover. (See figure 31.)
4.
Remove Remove the overflow tube by lifting
it while using a slight back and forth motion
to loosen it from the drain hole. The water in
the reservoir will flow down the drain. (See
figure 32.)
8
Reinstall inside front cover.
9
When the self-cleaning process stops
(approximately 45 minutes) the unit will
remain off for an additional 15 minutes. When
the clean cycle is completed, the display will
automatically switch back to set temperature
and unit will run as normal operation.
10
Clean the storage bin. (See INTERIOR
CLEANING). Sanatize the bin with a solution
of 1 tablespoon of bleach and 1 gallon of
warm water. Rinse thoroughly with clean
water.
11
To ensure the drain system is working
properly, pour 1 gallon of cool, fresh water
into the ice bin. The water should drain freely.
If the unit is equipped with a drain pump, it
should drain the ice bin.
When ice production resumes, the water fill valve
will energize, fill the water reservoir, and shut-
off after three minutes. The compressor begins
to operate and water flows over the evaporator
assembly (ice cube tray). Initially, the water flow
may not be uniform, causing uneven sized cubes
or water to spill into the ice storage bin. This is a
normal situation that will correct itself within the first
24 hours of operation.
IMPORTANT
•
Discard all ice produced in the first harvest.
•
If power gets interrupted during the self-
clean cycle, it will be necessary to repeat
the complete cleaning cycle after power is
restored.
Maintenance