Electrolux E36GF76HPS Installation Instructions - Page 7

When All Hookups are Complete, Before You Call for Service - 36 gas

Get Electrolux E36GF76HPS - 36inch Pro-Style Gas Range PDF manuals and user guides View all Electrolux E36GF76HPS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

36" GAS RANGE INSTALLATION INSTRUCTIONS 4. Adjust the "LOW" Setting of Regular Burner (see figure 7) on the Surface Burner Valves (Figure 8): a. Push in and turn control to LITE until burner ignites. b. Quickly turn knob to LOWEST POSITION. c. If burner goes out, reset control to OFF. d. Remove the surface burner control knob and decorative ring. e. Insert a thin-bladed screwdriver into the hollow valve stem and engage the slotted screw inside. Flame size can be increased or decreased by turning the screw. Turn counterclockwise to increase flame size. Turn clockwise to decrease flame size. Adjust flame until you can quickly turn knob from LITE to LOWEST POSITION without extinguishing the flame. Flame should be as small as possible without going out. Note: Air mixture adjustment is not required on surface burners. When All Hookups are Complete Make sure all controls are left in the OFF position. Before You Call for Service Read the Before You Call for Service Checklist and operating instructions in your Use and Care Guide. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Refer to your Use and Care Guide for Electrolux Service phone numbers, or call 1-877-4ELECTROLUX (1-877-435-3287). Figure 8 5. Adjust the "LOW" Setting of the Dual Burner (see Figure 7) on the Surface Burner Valve (Figure 9): Note: On the dual valve the low setting of each portion (rear portion of bridge burner and the center portion of bridge burner) should be adjusted individually. a. Push in and turn control to LITE until the rear portion of the bridge burner ignites only. b. Quickly turn knob to LOWEST POSITION. c. If burner goes out, reset control to OFF. d. Remove the surface burner control knob. e. The inner portion of the dual burner flame size can be increased or decreased by turning screw A (see Figure 9). Use screw B to adjust the flame size of the outer portion of the dual burner. Turn counterclockwise the screw to increase flame size. Turn clockwise the screw to decrease flame size. Adjust flame until you can quickly turn knob from LITE to LOWEST POSITION without extinguishing the flame. Flame should be as small as possible without going out. Note: Air mixture adjustment is not required on surface burners. B A Figure 9 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
7
36" GAS RANGE INSTALLATION INSTRUCTIONS
A
B
5.
Adjust the "LOW" Setting of the Dual Burner (see
Figure 7) on the Surface Burner Valve (Figure 9):
Note: On the dual valve the low setting of each portion
(rear portion of bridge burner and the center portion of
bridge burner) should be adjusted individually.
a.
Push in and turn control to LITE until the rear portion
of the bridge burner ignites only.
b.
Quickly
turn knob to LOWEST POSITION.
c.
If burner goes out, reset control to OFF.
d.
Remove the surface burner control knob.
e.
The inner portion of the dual burner flame size can be
increased or decreased by turning screw
A
(see Figure
9). Use screw
B
to adjust the flame size of the outer
portion of the dual burner. Turn counterclockwise the
screw to increase flame size. Turn clockwise the
screw to decrease flame size. Adjust flame until you
can quickly turn knob from LITE to LOWEST POSITION
without extinguishing the flame. Flame should be as
small as possible without going out.
Note:
Air mixture adjustment is not required on surface
burners.
Figure 9
Figure 8
4. Adjust the "LOW" Setting of Regular Burner (see
figure 7) on the Surface Burner Valves (Figure 8):
a.
Push in and turn control to LITE until burner ignites.
b.
Quickly
turn knob to LOWEST POSITION.
c.
If burner goes out, reset control to OFF.
d.
Remove the surface burner control knob and
decorative ring.
e.
Insert a thin-bladed screwdriver into the hollow valve
stem and engage the slotted screw inside. Flame size
can be increased or decreased by turning the screw.
Turn counterclockwise to increase flame size. Turn
clockwise to decrease flame size. Adjust flame until
you can quickly turn knob from LITE to LOWEST
POSITION without extinguishing the flame. Flame
should be as small as possible without going out.
Note:
Air mixture adjustment is not required on surface
burners.
When All Hookups are Complete
Make sure all controls are left in the OFF position.
Before You Call for Service
Read the Before You Call for Service Checklist and
operating instructions in your
Use and Care Guide
. It
may save you time and expense. The list includes
common occurrences that are not the result of defective
workmanship or materials in this appliance.
Refer to your
Use and Care Guide
for Electrolux Service
phone numbers, or call
1-877-4ELECTROLUX
(1-877-435-3287)
.