Electrolux EI30GS55LW Installation Instructions (All Languages) - Page 9

Check Operation

Get Electrolux EI30GS55LW PDF manuals and user guides View all Electrolux EI30GS55LW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS (Models with Sealed Top Burners) 10 Check Operation Refer to the Use and Care Guide packaged with the range for operating instructions and for care and cleaning of your range. Do not touch the elements or burners. They may be hot enough to cause burns. Remove all packaging from the oven before testing. 10.1 Install Burner Caps and Triple burner head This cooktop is equipped with sealed burners. A. Unpack the burner grates. B. Regular Burners: Burner heads and burner caps are already on the surface. Remove all tapes from burner caps and verify if they are correctly place on the burner heads (see Figure 9). Burner Cap Gas Opening Burner Head Electrode Figure 9 Burner Cap C. Triple Burner (if equipped): Remove all tapes from burner cap. Remove the burner cap and head. Remove and discard the packaging material. Replace head and cap on the triple burner. Be careful not to damage the electrode while placing the head over the orifice. Make sure electrode fits correctly into slot in burner head (see Figure 10). D. Be sure that all the burner caps and the triple burner head are correctly placed BEFORE using your cooktop. NOTE: There are no burner adjustments necessary on this cooktop. 10.2 Turn on Electrical Power and Open Main Shutoff Gas Valve 10.3 Check the Igniters Operation of electric igniters should be checked after range and supply line connectors have been carefully checked for leaks and range has been connected to electric power. To check for proper lighting: 1.Push in and turn a surface burner knob to the LITE position. You will hear the igniter sparking. 2. The surface burner should light when gas is available to the top burner. Each burner should light within four (4) seconds in normal operation after air has been purged from supply lines. Visually check that burner has lit. 3.Once the burner lights, the control knob should be rotated out of the LITE position. There are separate ignition devices for each burner. Try each knob separately until all burner valves have been checked. Burner Head Figure 10 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
9
30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS
(Models with Sealed Top Burners)
Figure 9
Burner Cap
Burner Head
Electrode
Gas Opening
10
Check Operation
Refer to the Use and Care Guide packaged with the
range for operating instructions and for care and
cleaning of your range.
Do not touch the elements or burners. They may be hot
enough to cause burns.
Remove all packaging from the oven before testing.
10.1
Install Burner Caps and Triple burner head
This cooktop is equipped with sealed burners.
A. Unpack the burner grates.
B.
Regular Burners
: Burner heads and burner caps are
already on the surface. Remove all tapes from burner
caps and verify if they are correctly place on the
burner heads (see Figure 9).
C.
Triple Burner (if equipped)
: Remove all tapes
from burner cap. Remove the burner cap and head.
Remove and discard the packaging material. Replace
head and cap on the triple burner.
Be careful not
to damage the electrode while placing the head
over the orifice.
Make sure electrode fits correctly
into slot in burner head
(see Figure 10).
D. Be sure that all the burner caps and the triple burner
head are correctly placed BEFORE using your cooktop.
NOTE:
There are no burner adjustments necessary on
this cooktop.
10.2
Turn on Electrical Power and Open Main
Shutoff Gas Valve
10.3
Check the Igniters
Operation of electric igniters should be checked after
range and supply line connectors have been carefully
checked for leaks and range has been connected to
electric power. To check for proper lighting:
1. Push in and turn a surface burner knob to the LITE
position. You will hear the igniter sparking.
2. The surface burner should light when gas is available
to the top burner. Each burner should light within
four (4) seconds in normal operation after air has been
purged from supply lines. Visually check that burner
has lit.
3. Once the burner lights, the control knob should be
rotated out of the LITE position.
There are separate ignition devices for each burner. Try
each knob separately until all burner valves have been
checked.
Figure 10
Burner Cap
Burner Head