Electrolux EI48HI55KS Complete Owner's Guide (Español) - Page 5
Electrolux EI48HI55KS Manual
![]() |
View all Electrolux EI48HI55KS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
List of materials- Electrical & Installation requirements List of Materials Electrical Requirements Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/ NFPA 70 (latest edition), or CSA Standards C22.194, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. A copy of the above code standards can be obtained from: National Fire Protection Association One Batterymarch Park Quincy, MA 02269 CSA International 8501 East Pleasant Valley Road Cleveland, OH 44131-5575 • A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required. • If the house has aluminum wiring, follow the procedure below: 1. Connect a section of solid copper wire to the pigtail leads. 2. Connect the aluminum wiring to the added section of copper wire using special co nectors and/or tools designed and UL listed for joining copper to aluminum. Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices. • Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood. • Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (la est edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances. CAUTION To reduce the risk of fire and electric shock, install this hood insert only with internal and remote blower models rated maximum 7.4 A (Electrolux™). Parts included in your hood insert Metal grease filters: - Model EI30HI55KS: 2 filters - Model EI36HI55KS: 3 filters - Model EI48HI55KS: 4 filters Hood insert with 4 halogen lamps installed. 1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct transition with damper. 4 - 5 x 45 mm mounting screws for cabinet 4 - 4.2 x 8 mm screws for 10" round ducting damper 2 - 18mm spacer screw (only for EI30HI55KS hood insert model) Parts Needed Home power supply cable 1 - ½" (1.3 cm) UL listed or CSA approved strain relief 3 - UL listed wire connectors 1 wall or roof cap Metal vent system Blower motor system - internal or remote (see "Blower Motor Options" section). • Level Drill 1¼" (3 cm) drill bit 11/8" (3 mm) drill bit • • Pencil Wire stripper or knife • Tape measure or ruler • • Pliers Caulking gun and weatherproof caulking compound Vent clamps Jigsaw or keyhole saw Flat-blade screwdriver Metal snips Phillips screwdriver Tools/Materials required Blower Motor Options (1 system is required with Vent Hood Insert) BLOWER MOTOR SYSTEM KITS MODEL EI06HIPIKS (600 cfm Int. Blower Kit) EI12HIPIKS (1200 cfm Int.Blower Kit) EI06HIPRKS (600 cfm Remote Blower Kit) EI12HIPRKS (1200 cfm Remote Blower Kit) RATING 3.7 A 7.4 A 3.7 A 7.4 A HOOD INSERT MODELS EI30HI55K5 EI36HI55K5 EI48HI55K5 • • • You can use your range hood model with this blower motor kit.
![](/manual_guide/products/electrolux-ei48hi55ks-complete-owners-guide-espa241ol-9f96e12/5.png)