Electrolux ELFW4222AW Complete Owners Guide English - Page 26

Problem, Possible Causes, Solutions, Preventive, Measures, Clean Washer

Page 26 highlights

26 Solutions to Common Problems PROBLEM POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES Residue • Moisture in washer. • Perform clean • Run dehumidifier in stains/ • Use of non-HE washer cycle. buildup, mold detergent. • Scrub gasket with Comet™ or mildew stains in gasket • Overdosing detergent. • Overloading wash drum. Spray Gel Mildew Stain Remover - use brush to remove stains. • Leaving a wet load set • Use only HE (high efficiency in washer. detergent) along with • Cold water washes recommended dosage. which may not • Remove wash load completely dissolve immediately upon cycle and remove completion. detergents. laundry room. • Avoid overfilling detergent and fabric softener compartments of dispenser. • Dry the inside of washer and gasket after every run. Residue • Moisture in the • Remove and clean dispenser • Avoid overfilling stains/ washer. buildup, mold • Use of non-HE or mildew detergent. stains in dispenser • Overdosing detergent. drawer and inserts with combination of ¾ cup liquid chlorine bleach and one gallon hot water. Rinse well, and repeat if necessary. When cleaning, wear rubber or detergent and fabric softener compartments of dispenser. latex gloves and protect floor and clothing from bleach damage. • Use only HE (high efficiency detergent) along with recommended dosage. Water in fold • Result of washing of flexible and part of normal • At the end of each wash, dry inside of gasket fold with gasket operation. clean dry towel all around gasket. Odor • Moisture in the • Perform clean washer • Leave door and washer. cycle. • Use of non-HE • At the end of each wash, detergent. dry inside of gasket fold with • Overdosing detergent. clean, dry towel all around • Leaving a wet load gasket. remain in washer. • Use only HE (high efficiency • Cold water washes which may not detergent) along with recommended dosage. completely dissolve • Remove wash load and remove immediately upon cycle detergents. completion. dispenser drawer open for a few hours after use or whenever washer is not in use. • Pour one cup liquid chlorine bleach in standpipe; let remain a day and flush with water.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

Solutions to Common Problems
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
PREVENTIVE
MEASURES
Residue
stains/
buildup, mold
or mildew
stains in
gasket
• Moisture in washer.
• Use of non-HE
detergent.
• Overdosing detergent.
• Overloading wash
drum.
• Leaving a wet load set
in washer.
• Cold water washes
which may not
completely dissolve
and remove
detergents.
• Perform clean
washer cycle.
• Scrub gasket with Comet™
Spray Gel Mildew Stain
Remover - use brush to
remove stains.
• Use only HE (high efficiency
detergent) along with
recommended dosage.
• Remove wash load
immediately upon cycle
completion.
• Run dehumidifier in
laundry room.
• Avoid overfilling
detergent and
fabric softener
compartments of
dispenser.
• Dry the inside of
washer and gasket
after every run.
Residue
stains/
buildup, mold
or mildew
stains in
dispenser
drawer
• Moisture in the
washer.
• Use of non-HE
detergent.
• Overdosing detergent.
• Remove and clean dispenser
and inserts with combination
of ¾ cup liquid chlorine
bleach and one gallon
hot water. Rinse well, and
repeat if necessary. When
cleaning, wear rubber or
latex gloves and protect floor
and clothing from bleach
damage.
• Use only HE (high efficiency
detergent) along with
recommended dosage.
• Avoid overfilling
detergent and
fabric softener
compartments of
dispenser.
Water in fold
of flexible
gasket
• Result of washing
and part of normal
operation.
• At the end of each wash,
dry inside of gasket fold with
clean dry towel all around
gasket.
Odor
• Moisture in the
washer.
• Use of non-HE
detergent.
• Overdosing detergent.
• Leaving a wet load
remain in washer.
• Cold water washes
which may not
completely dissolve
and remove
detergents.
• Perform
clean washer
cycle.
• At the end of each wash,
dry inside of gasket fold with
clean, dry towel all around
gasket.
• Use only HE (high efficiency
detergent) along with
recommended dosage.
• Remove wash load
immediately upon cycle
completion.
• Pour one cup liquid chlorine
bleach in standpipe; let
remain a day and flush with
water.
• Leave door and
dispenser drawer
open for a few
hours after use or
whenever washer is
not in use.
26