Electrolux EW30GS80RS Installation Instructions English Spanish French - Page 11
Range Installation
![]() |
View all Electrolux EW30GS80RS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS (Models with Sealed Top Burners) 9. Range Installation Important Note: Door removal is not a requirement for installation of the range, but is an added convenience. Refer to the Use and Care Guide for oven door removal instructions. Figure 13 Standard Installation 9.1 The range cooktop overlaps the countertop at the sides and the range rests on the floor. The cooktop is 31 1/2" (80 cm) wide. 9.2 Install base cabinets 30" (76,2 cm) apart. Make sure they are plumb and level before attaching cooktop. Shave raised countertop edge to clear 31 1/2" (80 cm) wide range top rim. 9.3 Install cabinet doors 32" (81,3 cm) min. apart so it will not interfere with range door opening. 9.4 Cutout countertop exactly as shown on page 4. For models equipped with Leveling Device: 9.5 Make sure the front leveling legs and the rear leveling device are setup higher than the height of the cabinet. 9.6 Remove and discard the two rear leveling legs, they are only in place to solidify the unit for the transport. 9.7 Install the anti-tip bracket at this point before placing the range at its final position. Follow the installation instructions on page 9 or on the anti-tip bracket template supplied with the range. 9.8 To provide an optimum installation, the top surface of the countertop must be level and flat (lie on the same plane) around the 3 sides that are adjacent to range cooktop. Proper adjustments to make the top flat should be made or gaps between the countertop and the range cooktop may occur. 9.9 To reduce the risk of damaging your appliance, do not handle or manipulate it by the cooktop or control console. Manipulate with care. 9.10 Position range in front of the cabinet opening. 9.11 Make sure that the cooktop which overhangs the countertop clears the countertop. If necessary, raise the unit by lowering the leveling legs. 9.12 Slide the range into the cutout opening and center it before leveling it. 9.13 Level the range (see section 10). The floor where the range is to be installed must be level. Follow the instructions under "Leveling the Range- Models Equipped with Leveling Device". 9.14 Adjust leveling legs so that the underside of the cooktop is sitting on the countertop. Carefully screw in (refer to Leveling the range: Models equipped with Leveling Device") the back leveling leg until the cooktop overhang touches slightly the countertop. Then carefully screw in the front two leveling legs until the cooktop overhang touches slightly the countertop. For models equipped with Leveling Leg only (no leveling device): 9.5 Make sure the four leveling legs (front and rear) are setup higher than the height of the cabinet (shown on page 3). 9.6 Install the anti-tip bracket at this point before placing the range at its final position. Follow the installation instructions on page 10 or on the anti-tip bracket template supplied with the range. 9.7 To provide an optimum installation, the top surface of the countertop must be level and flat (lie on the same plane) around the 3 sides that are adjacent to range cooktop. Proper adjustments to make the top flat should be made or gaps between the countertop and the range cooktop may occur. 9.8 To reduce the risk of damaging your appliance, do not handle or manipulate it by the cooktop. Manipulate with care. 9.9 Position range in front of the cabinet opening. 9.10 Make sure that the cooktop which overhangs the countertop clears the countertop. If necessary, raise the unit by lowering the leveling legs. 9.11 Level the range (see section 9). The floor where the range is to be installed must be level. Follow the instructions under "Leveling the Range- Models Equipped with Leveling Legs". 9.12 Slide the range into the cutout opening. IMPORTANT If Accessories Needed Installation With Backguard A backguard kit can be ordered through a Service Center. The cutout depth (21¾" (55,2 cm) Min., 221/8" (56,2 cm) Max.) needs to be increased to 24" (61 cm) when installing a backguard Installation With End Panel An end panel kit can be ordered through a Service Center. Installation With Side Panel A side panels kit can be ordered through a Service Center. Install cabinet doors 32" (81,3 cm) min. apart so as not to interfere with range door opening. 11
![](/manual_guide/products/electrolux-ew30gs80rs-installation-instructions-english-spanish-french-cfa7a09/11.png)