Epson EX90 User's Guide - Page 78

Resetting the Lamp Timer

Get Epson EX90 - XGA LCD Projector PDF manuals and user guides
UPC - 010343868656
View all Epson EX90 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

caution Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 7. Gently insert the new lamp along the guide rail. If it doesn't fit easily, make sure it's facing the correct way. Push the lamp down firmly where the label PUSH appears. 8. Once the lamp is fully inserted, tighten its screws. 9. Lower the lamp cover into place. (The opening should be almost covered, and the top of the cover should be flush with the top of the projector.) Then slide the cover closed and tighten the screw. note Be sure to seat the lamp fully and secure the lamp cover. If the lamp is not properly installed or the cover is loose, the lamp will not turn on. 10. Reset the lamp timer as described in the next section. note Do not reset the lamp timer if you have not replaced the lamp. If you do, the Lamp Hours will not accurately reflect the number of hours that the lamp has been used. Resetting the Lamp Timer You must reset the lamp timer after replacing the lamp to clear the Replace the Lamp warning message. Follow these steps: 1. Connect the power cable and turn on the projector. 2. Press the Menu button on the remote control or projector and select the Reset menu. Then press Enter. You see the following: 78 Maintenance and Transportation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
78
Maintenance and Transportation
7.
Gently insert the new lamp along the guide rail. If it doesn’t fit
easily, make sure it’s facing the correct way. Push the lamp down
firmly where the label
PUSH
appears.
8.
Once the lamp is fully inserted, tighten its screws.
9.
Lower the lamp cover into place. (The opening should be almost
covered, and the top of the cover should be flush with the top of
the projector.) Then slide the cover closed and tighten the screw.
10.
Reset the lamp timer as described in the next section.
Resetting the Lamp Timer
You must reset the lamp timer after replacing the lamp to clear the
Replace the Lamp
warning message. Follow these steps:
1.
Connect the power cable and turn on the projector.
2.
Press the
Menu
button on the remote control or projector and
select the
Reset
menu. Then press
Enter
. You see the following:
caution
Do not touch the glass
portion of the lamp
assembly. Touching the glass
could result in premature
lamp failure.
note
Be sure to seat the lamp fully
and secure the lamp cover. If
the lamp is not properly
installed or the cover is loose,
the lamp will not turn on.
note
Do not reset the lamp timer
if you have not replaced the
lamp. If you do, the Lamp
Hours will not accurately
reflect the number of hours
that the lamp has been used.