Epson LabelWorks LW-700 Quick Start and Warranty - Page 37

Solving Problems, Error messages

Get Epson LabelWorks LW-700 PDF manuals and user guides View all Epson LabelWorks LW-700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Solving Problems If you have a problem with your LabelWorks, check the display for error messages. See the online User's Guide for additional troubleshooting suggestions. Error messages Message Insert tape Check tape cartridge Check battery Change alkaline Explanation Turn the power off and install a tape cartridge. An incompatible tape cartridge has been installed. Check the tape cartridge. The batteries may be running out or installed incorrectly, nonalkaline batteries are being used with alkaline batteries, or old and new batteries are being used together. Turn the power off and replace batteries with new ones, or use the AC adapter. Make sure new batteries are installed correctly. 34 | Solving Problems Too many lines You have exceeded the maximum number of lines. Delete the lines indicated. No more sequence No. ! Sequence numbers have already been set. You can only enter one sequence per label. Text is too long. Continue? Entered text is too long for the specified label length. Press to confirm and continue printing. The label length will be adjusted automatically. Insert 24 mm tape! The label design can only be printed on 24 mm (1-inch) wide tape. Load wider tape Unable to print on the current tape. Use a wider tape. Printing length Shorten the label text. too long! No more barcode! Only one barcode can be added to a label. QR CODE too big! Do one of the following: use a wider tape, reduce the text or cell size, or lower the ECC (error correction) level. Overheated! The print head is too hot. Turn the power off and take out the tape cartridge. Allow the print head to cool before trying to print again.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
34
|
Solving Problems
Solving Problems
If you have a problem with your LabelWorks,
check the display for error messages. See the
online
User’s Guide
for additional
troubleshooting suggestions.
Error messages
Message
Explanation
Insert tape
Turn the power off and install a
tape cartridge.
Check tape
cartridge
An incompatible tape cartridge
has been installed. Check the tape
cartridge.
Check battery
Change alkaline
The batteries may be running out
or installed incorrectly, non-
alkaline batteries are being used
with alkaline batteries, or old and
new batteries are being used
together. Turn the power off and
replace batteries with new ones,
or use the AC adapter. Make sure
new batteries are installed
correctly.
Too many lines
You have exceeded the maximum
number of lines. Delete the lines
indicated.
No more
sequence No. !
Sequence numbers have already
been set. You can only enter one
sequence per label.
Text is too long.
Continue?
Entered text is too long for the
specified label length. Press
to confirm and continue printing.
The label length will be adjusted
automatically.
Insert 24 mm
tape!
The label design can only be
printed on 24 mm (1-inch) wide
tape.
Load wider tape
Unable to print on the current
tape. Use a wider tape.
Printing length
too long!
Shorten the label text.
No more barcode!
Only one barcode can be added to
a label.
QR CODE too big!
Do one of the following: use a
wider tape, reduce the text or cell
size, or lower the ECC (error
correction) level.
Overheated!
The print head is too hot. Turn the
power off and take out the tape
cartridge. Allow the print head to
cool before trying to print again.