Epson PowerLite S1 User Manual - Page 49

Only part of the image is displayed large/small, Use the Setting - lcd projector

Get Epson PowerLite S1 PDF manuals and user guides View all Epson PowerLite S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

When You Suspect a Problem 49 Only part of the image is displayed (large/small) • Change the resolution for the notebook computer or computer with an LCD screen. • Is the aspect ratio set correctly? • Has the computer been set for dual display? • Has the correct resolution been selected? • Has the position been adjusted correctly? • Is the E-Zoom function being used to enlarge the image? Change the resolution so that the image is displayed in the whole of the projection area, or set the image signal to external output only. See "Selecting the Input Source" on page 28. Press the [Aspect] button to set the aspect ratio to 4:3. See "Projecting in widescreen (changing aspect ratio)" on page 31. If dual display has been activated in the Display Properties of the connected computer's Control Panel, the projector will only display about half of the image on the computer screen. To display the whole of the image on the computer screen, turn off the dual display setting. Refer to the video driver manual for the computer's monitor for further details. Set the computer so that the signals that are output are compatible with this projector. Please refer to your computer's documentation for further details. See "Supported Display Resolutions" on page 64. Use the "Setting" → "Screen" → "Position" configuration menu to correctly adjust the display position. See "Setting menu" on page 39. Press the [Esc] button on the remote control to cancel E-Zoom. See "E-Zoom" on page 31.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
49
When You Suspect a Problem
Only part of the image is displayed (large/small)
•
Change the resolution for the notebook
computer or computer with an LCD screen.
Change the resolution so that the image is displayed in the whole of the
projection area, or set the image signal to external output only. See
“
Selecting
the Input Source
” on page 28
.
•
Is the aspect ratio set correctly?
Press the [Aspect] button to set the aspect ratio to 4:3. See
“
Projecting in
widescreen (changing aspect ratio)
” on page 31
.
•
Has the computer been set for dual display?
If dual display has been activated in the Display Properties of the connected
computer’s Control Panel, the projector will only display about half of the image
on the computer screen. To display the whole of the image on the computer
screen, turn off the dual display setting. Refer to the video driver manual for the
computer’s monitor for further details.
•
Has the correct resolution been selected?
Set the computer so that the signals that are output are compatible with this
projector. Please refer to your computer’s documentation for further details. See
“
Supported Display Resolutions
” on page 64
.
•
Has the position been adjusted correctly?
Use the “Setting”
→
“Screen”
→
“Position” configuration menu to correctly
adjust the display position. See
“
Setting menu
” on page 39
.
•
Is the E-Zoom function being used to enlarge
the image?
Press the [Esc] button on the remote control to cancel E-Zoom.
See
“
E-Zoom
” on page 31
.