Epson Stylus COLOR 777i Printer Basics - Page 34

Problems and Solutions, Setup and Software Installation Problems - drivers

Get Epson Stylus COLOR 777i - Ink Jet Printer PDF manuals and user guides View all Epson Stylus COLOR 777i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Problems and Solutions Below are some troubleshooting tips if you have any problems setting up your printer, installing software, getting good print quality, feeding paper, or other problems. Setup and Software Installation Problems The printer makes noise after ink cartridge installation. s The first time you install ink cartridges, the printer must charge its ink delivery system for a couple minutes. Wait until charging finishes (the Ppower light stops flashing) before you turn off the printer or it may charge improperly and use excess ink the next time you turn it on. If the printer stops moving or making noise, but the Ppower light is still flashing after 5 minutes, turn off the printer. If the light is still flashing when you turn it back on, see "Where To Get Help" on page 37. s Make sure the ink cartridge clamps are locked down completely and that no packing material remains in the printer. Turn off the printer, wait a moment, then turn it back on to clear the error. You're having problems installing the printer software. s Make sure your printer is turned on and the printer cable is securely connected at both ends. Then carefully follow the installation instructions on the Start Here sheet. Also make sure your system meets the requirements beginning on page 39. s Close your other applications, including any screen savers and virus protection software and install again. s If your printer icon (SC 777) doesn't appear in the Macintosh Chooser, you may have too many items in the Chooser. Delete any unused items and check the Chooser again. s Make sure that the Universal Serial Bus Controller is working properly in Device Manager; see your computer documentation. If it is not working, contact your computer dealer. s If you see an error message or the software doesn't install correctly on Windows 2000 or Windows NT, you may not have software installation privileges. s In Windows 2000, don't select Block under Control Panel> System> Hardware> Driver Signing; select Ignore or Warn instead. s If you're printing over a network, see your electronic Reference Guide for instructions on configuring your printer for use on a network. s If you're installing Corel Print House,™ you'll need to enter the product serial number located on the back of your Start Here sheet. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
30
Problems and Solutions
Below are some troubleshooting tips if you have any problems setting up your printer,
installing software, getting good print quality, feeding paper, or other problems.
Setup and Software Installation Problems
The printer makes noise after ink
cartridge installation.
■
The first time you install ink
cartridges, the printer must charge its
ink delivery system for a couple
minutes. Wait until charging finishes
(the
P
power light stops flashing)
before you turn off the printer or it
may charge improperly and use excess
ink the next time you turn it on. If
the printer stops moving or making
noise, but the
P
power light is still
flashing after 5 minutes, turn off the
printer. If the light is still flashing
when you turn it back on, see “Where
To Get Help” on page 37.
■
Make sure the ink cartridge clamps
are locked down completely and that
no packing material remains in the
printer. Turn off the printer, wait a
moment, then turn it back on to clear
the error.
You’re having problems installing the
printer software.
■
Make sure your printer is turned on
and the printer cable is securely
connected at both ends. Then
carefully follow the installation
instructions on the
Start Here
sheet.
Also make sure your system meets the
requirements beginning on page 39.
■
Close your other applications,
including any screen savers and virus
protection software and install again.
■
If your printer icon (SC 777) doesn’t
appear in the Macintosh Chooser,
you may have too many items in the
Chooser. Delete any unused items
and check the Chooser again.
■
Make sure that the Universal Serial
Bus Controller is working properly in
Device Manager; see your computer
documentation. If it is not working,
contact your computer dealer.
■
If you see an error message or the
software doesn’t install correctly on
Windows 2000 or Windows NT,
you may not have software
installation privileges.
■
In Windows 2000, don’t select
Block
under
Control Panel
>
System
>
Hardware
>
Driver Signing
; select
Ignore
or
Warn
instead.
■
If you’re printing over a network, see
your electronic
Reference Guide
for
instructions on configuring your
printer for use on a network.
■
If you’re installing Corel Print
House,
™
you’ll need to enter the
product serial number located on the
back of your
Start Here
sheet.