Epson SureColor S50675 High Production Edition Quick Reference Guide - Page 11

as possible. Place the black rollers within 0.20 inch 5 mm of the edges of the media.

Get Epson SureColor S50675 High Production Edition PDF manuals and user guides View all Epson SureColor S50675 High Production Edition manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

English Loading Media | 9 Caution: If the left edge of the media is not in the right position, perform steps 7 to 2 in reverse order and restart the loading process. Do not attempt to reposition the roll holders while they are inserted in the media roll. 9. Move to the front of the printer, grasp the media as shown, and raise the media loading lever. Then pull the media straight to the center of the after heater. 10. For the S50675/S70675, adjust the position of the pressure rollers. The black low pressure rollers are used for normal printing, and the green high pressure rollers for ink layering (or printing on transparent or white film). Their positions vary with the width of the media and the rollers used. • For normal printing, position the black rollers over the media and under the black rectangles. Make sure each rectangle has a black roller under it. Rollers that are beyond the width of the media should be positioned between the black rectangles. Place as many black rollers on the media as possible. Place the black rollers within 0.20 inch (5 mm) of the edges of the media. • For ink layering (or printing on transparent or white film), position the two green rollers under the black rectangles at the left and right sides of the media as close to the edge as possible. Move the black rollers between the black rectangles. Place the green rollers within 0.40 inch (10 mm) of the edges of the media. • You may need to shift the media slightly to the left or adjust its position to optimize media use. You will only be able to print between the green rollers when they are in use. When they are not in use, place the green rollers at the far left and right of the outside black rectangles.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
Loading Media
|
9
English
Caution:
If the left edge of the media is not in the right position, perform steps 7 to 2 in reverse order and
restart the loading process. Do not attempt to reposition the roll holders while they are inserted in the media
roll.
9.
Move to the front of the printer, grasp the media as shown, and raise the media loading lever. Then
pull the media straight to the center of the after heater.
10.
For the S50675/S70675, adjust the position of the pressure rollers. The black low pressure rollers are
used for normal printing, and the green high pressure rollers for ink layering (or printing on
transparent or white film). Their positions vary with the width of the media and the rollers used.
•
For normal printing, position the black rollers over the media and under the black rectangles.
Make sure each rectangle has a black roller under it. Rollers that are beyond the width of the
media should be positioned between the black rectangles. Place as many black rollers on the media
as possible. Place the black rollers within 0.20 inch (5 mm) of the edges of the media.
•
For ink layering (or printing on transparent or white film), position the two green rollers under
the black rectangles at the left and right sides of the media as close to the edge as possible. Move
the black rollers between the black rectangles. Place the green rollers within 0.40 inch (10 mm) of
the edges of the media.
•
You may need to shift the media slightly to the left or adjust its position to optimize media use.
You will only be able to print between the green rollers when they are in use. When they are not in
use, place the green rollers at the far left and right of the outside black rectangles.